Kohler 8/10/12RESVL manual Date and Time Menu, Networking Information Menus

Page 43

3.17 Date and Time Menu

The date and time will typically be set at controller power--up. To change the date, time, or time format (12 hour or 24 hour), use the Date and Time menu. See Figure 3-18.

3.18 Networking Information Menus

Use the networking menus to view and adjust communication settings for systems with remote RBUS devices such as a PIM or LCM or load shed kit, and for systems that use the Kohlerr OnCuer Plus Generator Management System.

RBUS is a proprietary RS-485 communications protocol.

The Networking Information menu leads to submenus for network and RBUS communication settings.

	Date and	Date:
	Time	Date:
	Time
		02Dec2011
		Time:
		12:34pm
		Time Format:
		12hr24hr
		<---- Return

tp6804

To change the date and time, press the Select button See Figure 3-7 for instructions.

			Figure 3-18Date and Time Menu
Networking---->	Networking---->		NS	See Figure 3-20.
	Status
Information
	Networking---->		NC	See Figure 3-21.
	Configuration

	RBUS	---->	RB	See Figure 3-22.
	Information

	<---- Return
				tp6810
Figure 3-19Networking Information Menu

TP-6880 10/14

Section 3 RDC2 Controller Operation 43

Image 43

Contents TP-6880 10/14a RDC2Controller Identification Accessory Number Accessory DescriptionProduct Identification Information Generator Set Identification NumbersTable of Contents Troubleshooting Scheduled MaintenanceDC2 Controller Operation Accidental starting Can cause severe injury or death Safety Precautions and InstructionsBattery Accidental StartingFire Can cause severe injury or death Engine Backfire/Flash FireExhaust System Carbon monoxide Can CauseHazardous voltage Will cause severe injury or death Fuel System Hazardous NoiseHot Parts Heavy EquipmentList of Related Literature Transfer Switch LiteratureAccessory Literature IntroductionEmission Compliance Period NameplateEmission Information Generator Set ApplicationService Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Load Control Module LCM AccessoriesCarburetor Heater Programmable Interface Module PIM1214 Service Views3Service View Generator Set Operation Prestart ChecklistGenerator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator SetExercise Automatic Operation with Other Transfer SwitchesSetting the Exerciser Unloaded Cycle Exercise with Complete System DiagnosticsLoaded Full-Speed Exercise with RXT only Power Failure During Exercise CycleSystem Diagnostics Unloaded Full-Speed ExerciseShutdowns FaultsATS Communication Errors Resetting the Controller after a Fault ShutdownFault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault MessagesGenerator Enclosure Thermostat Generator Set Operation TP-6880 10/14 Controls and Indicators RDC2 Generator Set/ Transfer Switch ControllerRDC2 Controller Operation LED Operation Controller Keypad LED IndicatorsButton Button FunctionActive Alert LCD DisplayProcedure to Change Settings Controller PowerBattery Charging Changing Settings7Changing Settings Changing Settings on the RDC2 ControllerProcedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller MenusEngine Metering Menu Overview MenuVoltage Calibration Generator Metering MenuGenset Run Time Menu Generator Set Information MenuVoltage Regulator VR Voltage Adj Setting the ExerciserAdjusting the Display Contrast Genset System MenuScreens on this page do not appear ATS Status MenuChanging ATS Configuration Settings ATS Configuration MenuNetworking Information Menus Date and Time MenuDhcp Networking Status SubmenuPassword Networking Configuration Submenu OnCue Plus PasswordDhcp Submenu 21Network Configuration Submenu 22RBUS Information Submenu Rbus InformationFrom Figure Remote Devices SubmenuProgrammable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit MenusEvent Log Procedure to View Event HistoryRDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch ControllerDescription Controller KeypadButton Button Function LED Indication5Status Displays, Generator Running Exercise Modes Exerciser ResetOnCue Plus Password Maintenance TimerDC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Low Oil Pressure Shutdown Oil Change ProcedureLubrication System Engine Oil RecommendationFill with oil Reset the maintenance timer on the controllerDrain the oil Replace the oil filterModel Resvl DC2 Resetting the Maintenance TimerSpark Plugs Model Resv RDC2Air Cleaner, 8RESV/RESVL Models Air Cleaner ServicePaper Element Service Cooling System Air Cleaner, 10/12RESV/RESVL ModelsHazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 USB Port TroubleshootingFault Messages IntroductionProblem Possible Cause Corrective Action TroubleshootingAnsi Appendix a AbbreviationsLCB Page TP-6880 10/14