Kohler 8/10/12RESVL Scheduled Maintenance, Accidental starting Can cause severe injury or death

Page 59

Section 5 Scheduled Maintenance

WARNING

Accidental starting.

Can cause severe injury or death.

Disconnect the battery cables before working on the generator set. Remove the negative (--) lead first when disconnecting the battery. Reconnect the negative (--) lead last when reconnecting the battery.

Disabling the generator set. Accidental starting can cause severe injury or death. Before working on the generator set or equipment connected to the set, disable the generator set as follows: (1) Press the generator set off/reset button to shut down the generator set. (2) Disconnect the power to the battery charger, if equipped. (3) Remove the battery cables, negative (--) lead first. Reconnect the negative (--) lead last when reconnecting the battery. Follow these precautions to prevent the starting of the generator set by the remote start/stop switch.

WARNING

Hot engine and exhaust system.

Can cause severe injury or death.

Do not work on the generator set until it cools.

Servicing the alternator. Hot parts can cause severe injury or death. Avoid touching the alternator field or exciter armature. When shorted, the alternator field and exciter armature become hot enough to cause severe burns.

Servicing the exhaust system. Hot parts can cause severe injury or death. Do not touch hot engine parts. The engine and exhaust system components become extremely hot during operation.

Servicing the engine heater. Hot parts can cause minor personal injury or property damage. Install the heater before connecting it to power. Operating the heater before installation can cause burns and component damage. Disconnect power to the heater and allow it to cool before servicing the heater or nearby parts.

DANGER

Hazardous voltage.

Will cause severe injury or death.

This equipment must be installed and serviced by qualified electrical personnel.

WARNING

Hazardous voltage. Moving parts.

Can cause severe injury or death.

Operate the generator set only when all guards and electrical enclosures are in place.

WARNING

Fire.

Can cause severe injury or death.

Do not smoke or permit flames or sparks near fuels or the fuel system.

Servicing the air cleaner. A sudden backfire can cause severe injury or death. Do not operate the generator set with the air cleaner removed.

Servicing the fuel system. A flash fire can cause severe injury or death. Do not smoke or permit flames or sparks near the carburetor, fuel line, fuel filter, fuel pump, or other potential sources of spilled fuels or fuel vapors. Catch fuels in an approved container when removing the fuel line or carburetor.

TP-6880 10/14

Section 5 Scheduled Maintenance 59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents TP-6880 10/14a RDC2Controller Identification Accessory Number Accessory DescriptionProduct Identification Information Generator Set Identification NumbersTable of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Accidental starting Can cause severe injury or death Safety Precautions and InstructionsBattery Accidental StartingFire Can cause severe injury or death Engine Backfire/Flash FireExhaust System Carbon monoxide Can CauseHazardous voltage Will cause severe injury or death Fuel System Hazardous NoiseHot Parts Heavy EquipmentList of Related Literature Transfer Switch LiteratureAccessory Literature IntroductionEmission Compliance Period NameplateEmission Information Generator Set ApplicationService Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Load Control Module LCM AccessoriesCarburetor Heater Programmable Interface Module PIM1214 Service Views3Service View Generator Set Operation Prestart ChecklistGenerator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator SetExercise Automatic Operation with Other Transfer SwitchesSetting the Exerciser Unloaded Cycle Exercise with Complete System DiagnosticsLoaded Full-Speed Exercise with RXT only Power Failure During Exercise CycleSystem Diagnostics Unloaded Full-Speed ExerciseShutdowns FaultsATS Communication Errors Resetting the Controller after a Fault ShutdownFault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault MessagesGenerator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators LED Operation Controller Keypad LED IndicatorsButton Button FunctionActive Alert LCD DisplayProcedure to Change Settings Controller PowerBattery Charging Changing Settings7Changing Settings Changing Settings on the RDC2 ControllerProcedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller MenusEngine Metering Menu Overview MenuVoltage Calibration Generator Metering MenuGenset Run Time Menu Generator Set Information MenuVoltage Regulator VR Voltage Adj Setting the ExerciserAdjusting the Display Contrast Genset System MenuScreens on this page do not appear ATS Status MenuChanging ATS Configuration Settings ATS Configuration MenuNetworking Information Menus Date and Time MenuDhcp Networking Status SubmenuDhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu 22RBUS Information Submenu Rbus InformationFrom Figure Remote Devices SubmenuProgrammable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit MenusEvent Log Procedure to View Event HistoryRDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch ControllerDescription Controller KeypadButton Button Function LED Indication5Status Displays, Generator Running Exercise Modes Exerciser ResetOnCue Plus Password Maintenance TimerDC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Low Oil Pressure Shutdown Oil Change ProcedureLubrication System Engine Oil RecommendationFill with oil Reset the maintenance timer on the controllerDrain the oil Replace the oil filterModel Resvl DC2 Resetting the Maintenance TimerSpark Plugs Model Resv RDC2Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Cooling System Air Cleaner, 10/12RESV/RESVL ModelsHazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 USB Port TroubleshootingFault Messages IntroductionProblem Possible Cause Corrective Action TroubleshootingAnsi Appendix a AbbreviationsLCB Page TP-6880 10/14
Top Page Image Contents