Shindaiwa DGW310DMC, DGW310MC owner manual Output Limitation, Power Consumption

Page 29

9-2. Output Limitation

Please refer to the table below, because electric tools and home appliances cannot be judged only by the

rated.

The rated output or the power consumption due to the efficiency and character of components.

Applicable Load (For reference only)

 

 

 

 

 

 

 

 

 

 

 

 

Capacity(kW)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1-P 100/110V

 

 

1-P 200/220V

3-P 200/

 

 

Loads

 

 

 

 

 

 

 

 

220V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Receptacle

 

Terminal

 

Terminal

Terminal

Total 3 terminal

 

 

 

 

 

 

 

 

 

 

Terminal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1pce

 

 

1 set

 

receptacle

1 set

set

 

 

 

 

 

 

 

 

 

 

total

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Electric Bulb, Heater, etc.

 

 

 

 

1.5

 

 

3.0

 

6.0

 

6.0

8.0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Electric Tools, etc. (Series

 

 

 

 

0.7

 

 

1.5

 

3.0

 

3.0

4.0

 

motor)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mercury Lamp (high power

 

 

 

 

0.6

 

 

1.2

 

2.4

 

2.4

3.2

 

factor type)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Submersible Pump,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Compressor, etc. (induction

 

 

 

 

0.6

 

 

1.2

 

2.4

 

2.4

3.2

4.0

motor)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-26-

 

 

 

 

Motor with brush

 

 

 

 

 

Series Motor

 

 

 

 

 

Induction Motor

Brushless Motor

 

 

 

 

 

The value described is

OUTPUT

for induction motor load and

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER CONSUMPTION

for the other equipment.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Caution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Be sure to use the frequency designated in the equipment incorporated in mercury

 

bulb or induction motor.

The load incorporated in motor may require bigger power than the rated power consumption.

So, consult with our authorized distributor or our engineering section to clarify.

When connection to use 2 or more sets, start the load one by one, not to start them simultaneously. When starting a mercury bulb ON again, wait for about 15 minutes until it cools down.

27

Image 29
Contents DGW310DMC DGW310MC Page Other types of caution Even som e of the items noted IntroductionSafety Guidelines Page Page Location of warning labels DGW310DMC DGW310MC SpecificationsUse DGW310DMC DGW310MC DGW310DMC Display Eco WeldingFrequency Selection Monitor LampOil Pressure Monitor Lamp Water Temperature Monitor LampBattery Charge Monitor Lamp How to connect remote control box Remote Control Box OptionElcb and Grounding Operation Check GroundingStop RUN StopElcb has activated Slow-down』FeatureSAE30 SAE20 Filling the radiator Filling the sub tankFull Fuel, Engine Oil and Water Leakage FuelFluid level is lower than the Lower level BatteryStart StartingKeep the engine idle for about 5 minutes Selection Welding Cable StoppingConnection Welding Cable PolarityDGW310DMC WeldingMIN MAX ECO ECODGW310MC Output Range P 200/220V 3-P 4-Wires21-P 200/220V P 100/110VOutput Power ConsumptionOutput Limitation Operation 』29 Simultaneous use of Generating and Welding Check and Maintenance Check Time Check Items Startup 1Change Engine Oil Change Oil Filter Clean/Change Air ElementClose Clean/Change Fuel StrainerChange Coolant/Water Long-Term StorageTroubleshooting Dual Regular( ) Memo