Shindaiwa DGW310MC, DGW310DMC owner manual Eco Welding, Display, Frequency Selection, Monitor Lamp

Page 12

5. Incorporated

5-1. Eco Welding

The equipment is incorporated in Eco Welding Feature that is aiming at performing

The low noise, the lower fuel consumption and the low gas emission than those of conventional models. When you turn the selector switch to Eco, you will be able to weld with Max 4.0mm rod at the slow down speed.

Caution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When welding is performed, do not turn the output selector switch which causes the burnout of the

 

 

switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Eco is designed for welding only. The breaker activates to TRIP, in case it is used for AC Output

 

5-2. Display

 

 

 

 

 

 

 

 

 

 

 

 

The equipment is incorporated in Digital Display. It displays

Voltage

,

Hour ,

Speed successively,

by changing the display selector switch.

』『

』『

 

 

 

 

 

 

 

 

Caution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

During operation, voltage meter always displays the voltage in 200/220V, 3-Phase both at the

 

 

breaker position

ON

and

OFF .

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5-3. Frequency Selection

 

 

 

 

 

 

 

 

 

 

Selector either 50 or 60Hz by the selector switch on the front panel, in accordance with the load

 

frequency.

 

 

 

 

 

 

 

 

 

 

 

 

5-4. Monitor Lamp

 

 

 

 

 

 

 

 

 

 

 

The equipment incorporates monitor lamps as Water Temperature

,

Battery Charging and

Oil

Pressure .

 

 

 

 

 

 

』 『

 

 

 

 

 

 

 

Under normal condition, when the starter switch is turned from STOP to REN , the lamps of, BATTERY

CHARGING

』『

 

and

OIL Pressure

turned To ON and all the lamps turn to OFF after the Engine starts.

When abnormality happens in running, monitor lamps flicker

And the engine stops automatically.

In the case the automatic shutdown is engaged, turn the starter switch to STOP once, and then restart the engine. When the automatic shutdown is engaged again, check which lamp turns ON or OFF and point out where the abnormality is.

Water Temp Charge Oil Pres

 

 

 

 

Preheat

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

Image 12
Contents DGW310DMC DGW310MC Page Introduction Other types of caution Even som e of the items notedSafety Guidelines Page Page Location of warning labels Specifications DGW310DMC DGW310MCUse DGW310DMC DGW310MC DGW310DMC Eco Welding DisplayFrequency Selection Monitor LampWater Temperature Monitor Lamp Battery Charge Monitor LampOil Pressure Monitor Lamp Remote Control Box Option How to connect remote control boxElcb and Grounding Grounding Operation CheckStop RUN StopSlow-down』Feature Elcb has activatedSAE30 SAE20 Filling the sub tank FullFilling the radiator Fuel Fuel, Engine Oil and Water LeakageBattery Fluid level is lower than the Lower levelStarting StartKeep the engine idle for about 5 minutes Stopping Selection Welding CablePolarity Connection Welding CableWelding DGW310DMCECO DGW310MCMIN MAX ECO P 200/220V 3-P 4-Wires Output Range21-P 200/220V P 100/110VPower Consumption Output LimitationOutput Operation 』29 Simultaneous use of Generating and Welding Check and Maintenance Check Time Check Items Startup 1Change Engine Oil Clean/Change Air Element Change Oil FilterClean/Change Fuel Strainer CloseLong-Term Storage Change Coolant/WaterTroubleshooting Regular Dual( ) Memo