Graco 332564B Output Register 12 Active Recipe Material B Flush Sequence

Page 30

Operation Using a Programmable Logic Controller (PLC)

OUTPUT REGISTER 12: Active Recipe Material B Flush Sequence

The Active Recipe Material B Flush Sequence register contains the number of the Flush Sequence (1 – 5) that is associated with the Catalyst pump of the current recipe.

•If the current recipe is invalid this value reflects the Flush Sequence associated with Material B pump of recipe 0.

•This value is 0 if the current recipe ratio is 0:1 (1K recipe)

OUTPUT REGISTER 13: Active Recipe Ratio Set Point

The Active Recipe Ratio Set Point data register contains the ratio set point associated with the current recipe.

•The value reported is the ratio antecedent multiplied by 100. The ratio consequent is always 1.

Example: Value = 250 >> A mix ratio of 2.5:1 (Material A to Material B)

•This value is 0 if the current recipe ratio is 0:1 (1K recipe)

OUTPUT REGISTER 14: Active Recipe Potlife Timeout Set Point

The Active Recipe Potlife Timeout Set Point register contains the set point for the potlife time associated with the current recipe in minutes.

•This value is 0 if the potlife time is disabled for the current recipe.

OUTPUT REGISTER 15: Actual Pump 1 Flow Rate

OUTPUT REGISTER 16: Actual Pump 2 Flow Rate

OUTPUT REGISTER 17: Actual Pump 3 Flow Rate

OUTPUT REGISTER 18: Actual Pump 4 Flow Rate

These registers contain the instantaneous flow rate of Pumps 1–4 in cc/min.

This is NOT the mix flow rate. For mix flow rate see Actual Mix Flow.

OUTPUT REGISTER 19: Actual Pump 1 Fluid

Pressure

OUTPUT REGISTER 20: Actual Pump 2 Fluid

Pressure

OUTPUT REGISTER 21: Actual Pump 3 Fluid

Pressure

OUTPUT REGISTER 22: Actual Pump 4 Fluid

Pressure

These registers contain the instantaneous fluid pressure on the outlet of pumps 1–4 in PSI.

OUTPUT REGISTER 23: Gun 1 Trigger Input Status

The Gun 1 Trigger Input Status register contains the status of the Gun Trigger Discrete Input.

•The value is 0 if the input is OPEN (gun not triggered).

•The value is 1 if the input is CLOSED (gun triggered).

This data register is valid only for systems configured to use the discrete input for the Gun Trigger. See Gun Trigger Signal, page 71.

OUTPUT REGISTER 24: Gun 2 Trigger Input Status

OUTPUT REGISTER 25: Gun 3 Trigger Input Status

OUTPUT REGISTER 26: Gun 4 Trigger Input Status

These registers are not used.

OUTPUT REGISTER 27: Safety Interlock Input Status

The Safety Interlock Input Status register contains the status of the Safety Interlock Discrete Input.

•The value will be 0 if the input is OPEN (Normal).

•The value will be 1 if the input is CLOSED (Safety Stop).

See Safety Interlock in Digital Inputs, page 25.

OUTPUT REGISTERS 28 – 36: DCS Command Structure

See Dynamic Command Description, page 47.

30

332564B

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Important Safety Instructions ProMix PD2K Proportioner for Automatic Spray ApplicationsContents Related Manuals Manual No DescriptionManual No Models ECB Labels0359 Model AC2000 High Pressure Identification Label Fire and Explosion Hazard Intrinsic Safety Personal Protective Equipment Keep Components a and B Separate Important Isocyanate ISO InformationIsocyanate Conditions Moisture Sensitivity of IsocyanatesGeneral Information USB Download Procedure Advanced Display Module ADMADM Display USB Upload Procedure ADM Keys and Indicators ADM Keys and Indicators FunctionSoft Key Icons Soft Key FunctionsKey Function Key Function Navigating the Screens Screen IconsPre-operation Checklist Power OnPre-Operation Tasks Initial System Setup Flush Before Using EquipmentValve Settings Without Color Change With Color ChangeOperation Using Automatic Display Module ADM Prime and Fill the SystemSpraying Purging Flush Mixed MaterialSingle Color System ShutdownFlush the System Color Change SystemDiscrete I/O Operation Using a Programmable Logic Controller PLCNetwork Communications and Discrete I/O PD2K Discrete I/O ConnectionsDigital Inputs Analog InputsDiscrete I/O Connections on Efcm KEYCommunication Gateway Module CGM Details CGM OverviewCGM Kits Network Communication I/O Data Map Output Register 00 Current System ModeNumber Operation Mode Description ProMix PD2K Network OutputsOutput Register 05 Actual Mix Flow Output Registers 01, 02, 03, and 04 Pump StatusPump States for Output Registers Description Ber Output Register 06 Actual Mix RatioOutput Registers 28 36 DCS Command Structure Output Register 14 Active Recipe Potlife Timeout Set PointOutput Register 27 Safety Interlock Input Status Output Register 12 Active Recipe Material B Flush SequenceOutput Register 37 Time Output Register 38 40 Software VersionOperation Using a Programmable Logic Controller PLC Network Output Data Map Read Only NonePSI = NAK = Busy= ACK = ERRInput Register 00 System Mode Command ProMix PD2K Network InputsInput Register 02 Flush/Prime Pump Command Input Register 03 Mix Pump 1 Control Set PointInput Register 07 Go to Recipe Number Input Register 09 Job Complete Input Register 08 Clear Active AlarmInput Registers 14 21 DCS Command Structure Input Register 10 Gun 1 TriggerOperation Using a Programmable Logic Controller PLC Network Input Data Map Write/Read 40180 Gun 3 Trigger Uint32 Operation Flow Charts Purge Mode SequenceFlush Pump Command Inactive Pump Flush and Prime SequencesColor Change Sequence ChangeMixing Sequence Standby Mix Ready? noAlarm Clearing Sequence Clear Active AlarmNetwork Communication Dynamic Command Structure DCS Dynamic Command DescriptionWrite User ID List of DCS CommandsDynamic Commands with Command ID DCSWrite Recipe Write Flush Sequence Write Fluid Control Mode Read User IDRead Recipe Read Flush SequenceRead Fluid Control Mode Read Job Info YymmddRead Alarm Info YymmdddwExample Ascii Character String Decode Algorithm Read Event Info Flow Control System Run Mode Screens Opening ScreenHome Screen Home Screen Key Description Details See Advanced Screen 1, page 82, to setKey Description Key Description Spray Screen, in Standby Mode Spray ScreenFill Screen Fill Screen, Color a SelectedUsage Screen Usage ScreenErrors Screen Jobs ScreenEvents Screen Setup Mode Screens Password ScreenSystem Screen Low Flow Timeout Mix Idle TimeoutMix No Flow Timeout Mix Pressure ToleranceMix At Wall Gun Hose LengthGun Hose Diameter Hose Length and DiameterEnable Gateway IDFluid Control Gun Trigger SignalFlow Control Setpoint Signal Manual OverrideRecipe Screen Flush Screen Pump Screen Default Settings Selected Default Settings Not SelectedPressure Alarm and Deviation Limits Pump Screen 3, Pressure Monitoring DisabledCalibration Screens Calibrate ScreenVolume Check Screen Enter Measured Volume of Solvent Maintenance Screens Maintenance ScreenMaintenance Screen 4, Color Valve Resets Advanced Screen Display Units Enable USB Downloads/UploadsLog 90% Full Advisory Enabled Download DepthCalibration Checks Pump Pressure CheckPerform the pressure check Pump Volume Check Solvent Meter Calibration Scroll to Calibrate Screen 3,Color Change Single Color SystemsMultiple Color Systems System Errors To Clear Error and RestartGun Trigger Input Function Error Codes Purge Errors Code Type Description Problem Cause SolutionMix Errors Code Type Description Problem Cause Solution Pumping Errors Code Type Description Problem Cause Solution Code Type Description Problem Cause Solution EBH#SAD1 Pressure Errors Code Type Description Problem Cause Solution Qadx QbdxCA0X System Errors Code Type Description Problem Cause SolutionEmix CAC#Cagx CDC#Cddx USB Errors Code Type Description Problem Cause Solution Wxud USBWxuu B9AX B9BXB9SX ENS0 Calibration Errors Code Type Name DescriptionEND# ENT#Maintenance Errors Code Type Name DescriptionCleaning the ADM MaintenancePreventive Maintenance Schedule FlushingTechnical Data Positive Displacement Metric ProportionerGraco Standard Warranty Graco InformationFor Graco Canada Customers
Top Page Image Contents