Grizzly G0705 owner manual Inventory, Crate Contents Figures 11 Qty, Not Shown

Page 18

Inventory

The following is a description of the main compo- nents shipped with your machine.

Crate Contents (Figures 11 & 12)		Qty
A.	Cabinet Base	1
B.	Machine	1
C.	Toolbox	1
D.	Drill Chuck B16 1–13mm	1
E.	Drill Chuck Arbor R8–B16	1
F.	Lug Wrench	1
G.	T-Bolt Assemblies	2
	—T-Bolt M14-2 x 55	2
	—Flat Washer 14mm	2
	—Hex Bolt M14-2	2
H.	Drill Chuck Key	1
I.	Drift Key	1
J.	Collet Adapter R8 to MT#3	1
K.	Collet Adapter MT#3 to MT#2	1
L.	Bottle For Oil	1
Not Shown
•	Hex Wrenches 3, 4, 5mm	1 Each
•	Hex Bolts M10-1.25 x 140	4
•	Flat Washers 10mm	4
•	Lock Washers 10mm	4
•	Open-End Combo Wrench 17/19mm	1
•	Hex Bolts M12-1.75 x 40	4
•	Hex Nuts M12-1.75	4
•	Cap Screws M6-1 x 16	3
•	Flat Washers 6mm	3
•	Drawbar	1

-16-

A

B

Figure 11. Main inventory.

C

H

G

E

L
										D
		K

				J
						I
								F

Figure 12. Inventory.

Model G0705 (Mfg. since 09/09)

Image 18

Contents Model G0705 Page Table of Contents Contact Info IntroductionManual Accuracy Machine DescriptionIdentification Machine Data Sheet Other Features Wearing Proper APPAREL. Do not wear SafetySafety Instructions for Machinery Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Additional Safety for Mill/Drills Full-Load Current Rating Power SupplyAvailability Circuit InformationVoltage Conversion Grounding RequirementsExtension Cords Minimum Gauge Size 12 AWGTo rewire the Model G0705 for 110V opera- tion 110V ConversionJumper positions on terminal block Cord rewired for Model G0705 Mfg. since 09/09 Unpacking SetupNeeded for Setup Description QtyCrate Contents Figures 11 Qty InventoryNot Shown Cleanup Before cleaning, gather the followingSite Considerations Using the Included Leveling Bolt Mounting OptionsUsing Machine Mounts Mounting to Shop FloorAssembly Mounting to a WorkbenchTo assemble your machine Moving & Placing Machine LevelingTo move your machine into position Test Run Break-In To break in the spindleOperations Operation OverviewBasic Controls Spindle controls Model G0705 Mfg. since 09/09Head crank Calculating Spindle Speed for Milling Cutting Speeds for High Speed Steel HSS Cutting ToolsTo calculate the needed spindle speed in RPM To change spindle speeds Speed ChangesTools Needed Qty PositionUsing the Drill Bit Speed Chart Calculating Spindle Speed for DrillingLubrication Suggestions To operate the micro-adjustment handwheel Spindle HeightTo install tooling Loading ToolingTo remove tooling To install the drill chuck onto the arbor Drill Chuck Arbor Collet AdaptersTo use the drift key Depth Stop To calibrate the depth stopLongitudinal Feed Table TravelGraduated Dials Cross FeedG9299-10 Yuasa-Type Rotary Table AccessoriesH2689-R-8 Quick Change Collet Set G1076-52-PC. Clamping KitG9765-9-PC. Ball End Mill Set H8370-Power Feed for MillsG2861-Face Mill G4051-Carbide Insert for Face Mill G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder SetMaintenance Cleaning ProtectingSchedule Points requiring periodic lubrication are LubricationTable Leadscrews Items Needed QtyBelts Belt tension Model G0705 Mfg. since 09/09Service TroubleshootingSymptom Possible Cause Possible Solution To adjust the table gibs To adjust the spring tensionGibs Return Spring Adjusting spring tension Tighten the black thumb knob Leadscrew BacklashWiring Wiring Safety InstructionsG0705 Wiring Diagram Electrical component locations Headstock Headstock Parts List DescriptionPCAP05 Base Base Parts List Electrical Components Breakdown and List 309Labels Breakdown and List Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY