Grizzly G0705 owner manual Assembly, Mounting to a Workbench, To assemble your machine

Page 23

Mounting to a Workbench

If you are placing the machine on an existing workbench, it must be securely attached to the workbench.

The strongest mounting option is a "Through Mount" where holes are drilled all the way through the workbench, and hex bolts, washers, and hex nuts are used to secure machine to the work- bench.

Bolt

Flat Washer

Machine Base

Workbench

Flat Washer

Lock Washer

Hex Nut

Figure 18. Example of a through mount setup.

Another option for mounting is a "Direct Mount" where the machine is simply secured to the work- bench with a lag screw.

Lag Screw

Flat Washer

Machine Base

Workbench

Figure 19. Example of a direct mount setup.

Assembly

Assembly of the Model G0705 consists of attach- ing the three handwheel handles to the machine.

To assemble your machine:

1.Use one M6-1 x 16 cap screw and 6mm flat washer to install each handwheel in the loca- tions shown in Figure 20.

Figure 20. Table handwheel handles.

Model G0705 (Mfg. since 09/09)

-21-

Image 23

Contents Model G0705 Page Table of Contents Machine Description IntroductionManual Accuracy Contact InfoIdentification Machine Data Sheet Other Features Hearing PROTECTION. Always wear hear SafetySafety Instructions for Machinery Wearing Proper APPAREL. Do not wearSafety Instructions for Machinery Additional Safety for Mill/Drills Circuit Information Power SupplyAvailability Full-Load Current RatingMinimum Gauge Size 12 AWG Grounding RequirementsExtension Cords Voltage Conversion110V Conversion To rewire the Model G0705 for 110V opera- tionJumper positions on terminal block Cord rewired for Model G0705 Mfg. since 09/09 Description Qty SetupNeeded for Setup UnpackingNot Shown Crate Contents Figures 11 QtyInventory Before cleaning, gather the following CleanupSite Considerations Mounting Options Using the Included Leveling BoltMounting to Shop Floor Using Machine MountsTo assemble your machine AssemblyMounting to a Workbench To move your machine into position Moving & Placing MachineLeveling Test Run To break in the spindle Break-InOperation Overview OperationsSpindle controls Model G0705 Mfg. since 09/09 Basic ControlsHead crank To calculate the needed spindle speed in RPM Calculating Spindle Speed for MillingCutting Speeds for High Speed Steel HSS Cutting Tools Position Speed ChangesTools Needed Qty To change spindle speedsLubrication Suggestions Using the Drill Bit Speed ChartCalculating Spindle Speed for Drilling Spindle Height To operate the micro-adjustment handwheelTo remove tooling To install toolingLoading Tooling To use the drift key To install the drill chuck onto the arborDrill Chuck Arbor Collet Adapters To calibrate the depth stop Depth StopCross Feed Table TravelGraduated Dials Longitudinal FeedG1076-52-PC. Clamping Kit AccessoriesH2689-R-8 Quick Change Collet Set G9299-10 Yuasa-Type Rotary TableG5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder Set H8370-Power Feed for MillsG2861-Face Mill G4051-Carbide Insert for Face Mill G9765-9-PC. Ball End Mill SetSchedule MaintenanceCleaning Protecting Items Needed Qty LubricationTable Leadscrews Points requiring periodic lubrication areBelt tension Model G0705 Mfg. since 09/09 BeltsTroubleshooting ServiceSymptom Possible Cause Possible Solution Gibs Return Spring To adjust the table gibsTo adjust the spring tension Leadscrew Backlash Adjusting spring tension Tighten the black thumb knobWiring Safety Instructions WiringG0705 Wiring Diagram Electrical component locations Headstock Description Headstock Parts ListPCAP05 Base Base Parts List 309 Electrical Components Breakdown and ListLabels Breakdown and List Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY