Grizzly owner manual Basic Controls, Spindle controls Model G0705 Mfg. since 09/09

Page 28

8.For milling operations, loosens the quill lock lever and uses the quill feed lever or the fine feed knob to set the cutting tool height according to the workpiece. Then, presses the FORWARD or REVERSE button to start the spindle and uses the table handwheels to move the table so the cutter removes mate- rial evenly from the workpiece.

For drilling operations, presses the FORWARD button and uses the quill feed lever or fine feed knob to lower the drill bit into the workpiece, then raises the drill bit out of the workpiece using the same controls.

9.Presses the STOP button to stop the spin- dle.

-26-

Basic Controls

Use the descriptions and figures below to become familiar with the basic controls of your machine.

Depth Stop: Stops the spindle travel at a pre- determined depth.

Quill Lock: Locks the quill in position.

Depth

Stop

Quill lock

Figure 23. Head controls.

Fine Downfeed Handwheel: Provides fine con- trol over vertical spindle travel.

Locking Knob: Engages/disengages the micro- adjustment handwheel.

Quill Downfeed Levers: Provide coarse control over vertical spindle travel.

Fine Downfeed

Handwheel

Locking Knob

Quill Downfeed Levers

Figure 24. Spindle controls.

Model G0705 (Mfg. since 09/09)

Image 28

Contents Model G0705 Page Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Machine Data Sheet Other Features Safety Safety Instructions for MachineryWearing Proper APPAREL. Do not wear Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Additional Safety for Mill/Drills Power Supply AvailabilityFull-Load Current Rating Circuit InformationGrounding Requirements Extension CordsVoltage Conversion Minimum Gauge Size 12 AWGTo rewire the Model G0705 for 110V opera- tion 110V ConversionJumper positions on terminal block Cord rewired for Model G0705 Mfg. since 09/09 Setup Needed for SetupUnpacking Description QtyInventory Crate Contents Figures 11 QtyNot Shown Cleanup Before cleaning, gather the followingSite Considerations Using the Included Leveling Bolt Mounting OptionsUsing Machine Mounts Mounting to Shop FloorMounting to a Workbench AssemblyTo assemble your machine Leveling Moving & Placing MachineTo move your machine into position Test Run Break-In To break in the spindleOperations Operation OverviewBasic Controls Spindle controls Model G0705 Mfg. since 09/09Head crank Cutting Speeds for High Speed Steel HSS Cutting Tools Calculating Spindle Speed for MillingTo calculate the needed spindle speed in RPM Speed Changes Tools Needed QtyTo change spindle speeds PositionCalculating Spindle Speed for Drilling Using the Drill Bit Speed ChartLubrication Suggestions To operate the micro-adjustment handwheel Spindle HeightLoading Tooling To install toolingTo remove tooling Drill Chuck Arbor Collet Adapters To install the drill chuck onto the arborTo use the drift key Depth Stop To calibrate the depth stopTable Travel Graduated DialsLongitudinal Feed Cross FeedAccessories H2689-R-8 Quick Change Collet SetG9299-10 Yuasa-Type Rotary Table G1076-52-PC. Clamping KitH8370-Power Feed for Mills G2861-Face Mill G4051-Carbide Insert for Face MillG9765-9-PC. Ball End Mill Set G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder SetCleaning Protecting MaintenanceSchedule Lubrication Table LeadscrewsPoints requiring periodic lubrication are Items Needed QtyBelts Belt tension Model G0705 Mfg. since 09/09Service TroubleshootingSymptom Possible Cause Possible Solution To adjust the spring tension To adjust the table gibsGibs Return Spring Adjusting spring tension Tighten the black thumb knob Leadscrew BacklashWiring Wiring Safety InstructionsG0705 Wiring Diagram Electrical component locations Headstock Headstock Parts List DescriptionPCAP05 Base Base Parts List Electrical Components Breakdown and List 309Labels Breakdown and List Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY