Grizzly G0705 owner manual Labels Breakdown and List

Page 56

Labels Breakdown and List

402 403

401

	404
405	405
405
	406

407

408

409

REF	PART #	DESCRIPTION

401	P0705401	MACHINE ID LABEL
402	PLABEL-11B	SAFETY GLASSES LABEL
403	PLABEL-55A	ENTANGLEMENT LABEL
404	PLABEL-12C	READ MANUAL LABEL
405	PLABEL-14A	ELECTRICITY LABEL

REF	PART #	DESCRIPTION

406	PPAINT-11	PUTTY TOUCH UP PAINT
407	P0705407	CUTTER WARNING LABEL
408	PPAINT-1	GREEN TOUCH UP PAINT
409	P0705409	MODEL NUMBER LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-54-	Model G0705 (Mfg. since 09/09)

Image 56

Contents Model G0705 Page Table of Contents Introduction Manual AccuracyContact Info Machine DescriptionIdentification Machine Data Sheet Other Features Safety Safety Instructions for MachineryWearing Proper APPAREL. Do not wear Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Additional Safety for Mill/Drills Power Supply AvailabilityFull-Load Current Rating Circuit InformationGrounding Requirements Extension CordsVoltage Conversion Minimum Gauge Size 12 AWGTo rewire the Model G0705 for 110V opera- tion 110V ConversionJumper positions on terminal block Cord rewired for Model G0705 Mfg. since 09/09 Setup Needed for SetupUnpacking Description QtyNot Shown Crate Contents Figures 11 QtyInventory Cleanup Before cleaning, gather the followingSite Considerations Using the Included Leveling Bolt Mounting OptionsUsing Machine Mounts Mounting to Shop FloorTo assemble your machine AssemblyMounting to a Workbench To move your machine into position Moving & Placing MachineLeveling Test Run Break-In To break in the spindleOperations Operation OverviewBasic Controls Spindle controls Model G0705 Mfg. since 09/09Head crank To calculate the needed spindle speed in RPM Calculating Spindle Speed for MillingCutting Speeds for High Speed Steel HSS Cutting Tools Speed Changes Tools Needed QtyTo change spindle speeds PositionLubrication Suggestions Using the Drill Bit Speed ChartCalculating Spindle Speed for Drilling To operate the micro-adjustment handwheel Spindle HeightTo remove tooling To install toolingLoading Tooling To use the drift key To install the drill chuck onto the arborDrill Chuck Arbor Collet Adapters Depth Stop To calibrate the depth stopTable Travel Graduated DialsLongitudinal Feed Cross FeedAccessories H2689-R-8 Quick Change Collet SetG9299-10 Yuasa-Type Rotary Table G1076-52-PC. Clamping KitH8370-Power Feed for Mills G2861-Face Mill G4051-Carbide Insert for Face MillG9765-9-PC. Ball End Mill Set G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder SetSchedule MaintenanceCleaning Protecting Lubrication Table LeadscrewsPoints requiring periodic lubrication are Items Needed QtyBelts Belt tension Model G0705 Mfg. since 09/09Service TroubleshootingSymptom Possible Cause Possible Solution Gibs Return Spring To adjust the table gibsTo adjust the spring tension Adjusting spring tension Tighten the black thumb knob Leadscrew BacklashWiring Wiring Safety InstructionsG0705 Wiring Diagram Electrical component locations Headstock Headstock Parts List DescriptionPCAP05 Base Base Parts List Electrical Components Breakdown and List 309Labels Breakdown and List Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY