Grizzly G0705 owner manual Break-In, To break in the spindle

Page 26

6.Press the STOP button to stop the machine. Allow the spindle to stop rotating before pro- ceeding.

7.Repeat Step 5 with the REVERSE button. The spindle should rotate in the opposite direction.

8.Press the EMERGENCY STOP button to stop the machine. Allow the spindle to stop rotating before proceeding.

9.WITHOUT resetting the switch, press the FORWARD button. The machine should not start.

—If the machine does not start, the EMERGENCY STOP button safety feature is working correctly. The Test Run is com- plete.

—If the machine does start (with the stop button pushed in), immediately disconnect power to the machine. The OFF button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

-24-

Break-In

NOTICE

Failure to follow spindle break-in proce- dures will likely cause rapid deterioration of the spindle and other related parts and may void the warranty.

NOTICE

DO NOT leave the area while break-in pro- cedure is under way. You must be ready to stop the machine if any problem occurs.

It is essential to closely follow the proper break-in procedures to ensure trouble free performance. Complete this process once you have familiarized yourself with all instructions in this manual.

To break in the spindle:

1.Make sure the machine has been properly lubricated. Refer to Lubrication on Page 39.

2.Make sure the spindle area is free of obstruc- tions.

3.Set the spindle speed to the lowest RPM. Refer to Speed Changes on Page 29.

4. Turn the spindle ON and let it run for a mini- mum of 10 minutes. Repeat this step for each RPM setting. Refer to Speed Changes on Page 29.

Model G0705 (Mfg. since 09/09)

Image 26

Contents Model G0705 Page Table of Contents Contact Info IntroductionManual Accuracy Machine DescriptionIdentification Machine Data Sheet Other Features Wearing Proper APPAREL. Do not wear SafetySafety Instructions for Machinery Hearing PROTECTION. Always wear hearSafety Instructions for Machinery Additional Safety for Mill/Drills Full-Load Current Rating Power SupplyAvailability Circuit InformationVoltage Conversion Grounding RequirementsExtension Cords Minimum Gauge Size 12 AWGTo rewire the Model G0705 for 110V opera- tion 110V ConversionJumper positions on terminal block Cord rewired for Model G0705 Mfg. since 09/09 Unpacking SetupNeeded for Setup Description QtyNot Shown Crate Contents Figures 11 QtyInventory Cleanup Before cleaning, gather the followingSite Considerations Using the Included Leveling Bolt Mounting OptionsUsing Machine Mounts Mounting to Shop Floor To assemble your machine Assembly Mounting to a Workbench To move your machine into position Moving & Placing MachineLeveling Test Run Break-In To break in the spindleOperations Operation OverviewBasic Controls Spindle controls Model G0705 Mfg. since 09/09Head crank To calculate the needed spindle speed in RPM Calculating Spindle Speed for MillingCutting Speeds for High Speed Steel HSS Cutting Tools To change spindle speeds Speed ChangesTools Needed Qty PositionLubrication Suggestions Using the Drill Bit Speed ChartCalculating Spindle Speed for Drilling To operate the micro-adjustment handwheel Spindle HeightTo remove tooling To install toolingLoading Tooling To use the drift key To install the drill chuck onto the arborDrill Chuck Arbor Collet Adapters Depth Stop To calibrate the depth stopLongitudinal Feed Table TravelGraduated Dials Cross FeedG9299-10 Yuasa-Type Rotary Table AccessoriesH2689-R-8 Quick Change Collet Set G1076-52-PC. Clamping KitG9765-9-PC. Ball End Mill Set H8370-Power Feed for MillsG2861-Face Mill G4051-Carbide Insert for Face Mill G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder SetSchedule MaintenanceCleaning Protecting Points requiring periodic lubrication are LubricationTable Leadscrews Items Needed QtyBelts Belt tension Model G0705 Mfg. since 09/09Service TroubleshootingSymptom Possible Cause Possible Solution Gibs Return Spring To adjust the table gibsTo adjust the spring tension Adjusting spring tension Tighten the black thumb knob Leadscrew BacklashWiring Wiring Safety InstructionsG0705 Wiring Diagram Electrical component locations Headstock Headstock Parts List DescriptionPCAP05 Base Base Parts List Electrical Components Breakdown and List 309Labels Breakdown and List Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY