Grizzly G0705 G2861-Face Mill G4051-Carbide Insert for Face Mill, G9765-9-PC. Ball End Mill Set

Page 39

G2861—Face Mill

G4051—Carbide Insert for Face Mill

This 21/2" Face Mill accepts four carbide inserts (not included). Comes with an R-8 arbor.

Figure 49. G2861 Face Mill.

G9760—20-PC. 2 & 4 Flute TiN End Mill Set. Includes these sizes and styles in two and four flute styles: 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/8", 11/16", and 3/4".

Figure 50. G9760 20-PC End Mill Set.

G9765—9-PC. Ball End Mill Set

Features 2 flute ball nose end mills. Includes the following sizes: 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8" and 3/4".

Figure 51. G9765 9 PC. Ball End Mill Set.

Model G0705 (Mfg. since 09/09)

G5641—1-2-3 Blocks

G9815—Parallel Set

H5556—Edge Finder Set

G5641

H5556

G9815

Figure 52. G5641 1-2-3 Blocks, G9815 Parallel

Set, and H5556 Edge Finder Set.

H8370—Power Feed for Mills

If you want to get the most out of your mill, you really need a power feed. This power feed comes with everything required to start milling with exact control. Comes supplied with a mounting bracket, gear, auto-stop limit switch with moveable stop pins, gear guard, and motor. Specs: 0–140 RPM, 200 RPM rapid switch, 440 in/lb. maximum torque, 110V 60Hz motor, 4:1 bevel drive gear.

Figure 53. H8370 Power Feed.

-37-

Image 39

Contents Model G0705 Page Table of Contents Machine Description IntroductionManual Accuracy Contact InfoIdentification Machine Data Sheet Other Features Hearing PROTECTION. Always wear hear SafetySafety Instructions for Machinery Wearing Proper APPAREL. Do not wearSafety Instructions for Machinery Additional Safety for Mill/Drills Circuit Information Power SupplyAvailability Full-Load Current RatingMinimum Gauge Size 12 AWG Grounding RequirementsExtension Cords Voltage Conversion110V Conversion To rewire the Model G0705 for 110V opera- tionJumper positions on terminal block Cord rewired for Model G0705 Mfg. since 09/09 Description Qty SetupNeeded for Setup UnpackingCrate Contents Figures 11 Qty InventoryNot Shown Before cleaning, gather the following CleanupSite Considerations Mounting Options Using the Included Leveling BoltMounting to Shop Floor Using Machine MountsAssembly Mounting to a WorkbenchTo assemble your machine Moving & Placing Machine LevelingTo move your machine into position Test Run To break in the spindle Break-InOperation Overview OperationsSpindle controls Model G0705 Mfg. since 09/09 Basic ControlsHead crank Calculating Spindle Speed for Milling Cutting Speeds for High Speed Steel HSS Cutting ToolsTo calculate the needed spindle speed in RPM Position Speed ChangesTools Needed Qty To change spindle speedsUsing the Drill Bit Speed Chart Calculating Spindle Speed for DrillingLubrication Suggestions Spindle Height To operate the micro-adjustment handwheelTo install tooling Loading ToolingTo remove tooling To install the drill chuck onto the arbor Drill Chuck Arbor Collet AdaptersTo use the drift key To calibrate the depth stop Depth StopCross Feed Table TravelGraduated Dials Longitudinal FeedG1076-52-PC. Clamping Kit AccessoriesH2689-R-8 Quick Change Collet Set G9299-10 Yuasa-Type Rotary TableG5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder Set H8370-Power Feed for MillsG2861-Face Mill G4051-Carbide Insert for Face Mill G9765-9-PC. Ball End Mill SetMaintenance Cleaning ProtectingSchedule Items Needed Qty LubricationTable Leadscrews Points requiring periodic lubrication areBelt tension Model G0705 Mfg. since 09/09 BeltsTroubleshooting ServiceSymptom Possible Cause Possible Solution To adjust the table gibs To adjust the spring tensionGibs Return Spring Leadscrew Backlash Adjusting spring tension Tighten the black thumb knobWiring Safety Instructions WiringG0705 Wiring Diagram Electrical component locations Headstock Description Headstock Parts ListPCAP05 Base Base Parts List 309 Electrical Components Breakdown and ListLabels Breakdown and List Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY