Bostitch LPF28WW Maintaining the Pneumatic Tool, Replacement Parts, Assembly Procedure for Seals

Page 10

LPF21PL-LPF33PT-LPF28WW_9R189680RC_BOS_MAN_JM_166762RevC_FSeries_Man.qxd 11/26/12 10:30 AM

MAINTAINING THE PNEUMATIC TOOL

When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.

Pusher spring (constant force spring). Caution must be used when working with the spring assembly. The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand. Also the edges of the spring are very thin and could cut. Care must also be taken to insure no permanent kinks are put in the spring as this will reduce the springs force.

REPLACEMENT PARTS:

Use only Bostitch replacement parts.

ASSEMBLY PROCEDURE FOR SEALS:

When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE or equivalent on all “O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of Bostitch Air Tool Lubricant through the air line fitting before testing.

AIR SUPPLY-PRESSURE AND VOLUME:

Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air supply from the tool to the supply source for restrictive connectors, swivel fittings, low points containing water and anything else that would prevent full volume flow of air to the tool.

10

Image 10
Contents LPF21PL / LPF33PT / LPF28WW Introduction IndexLoading Tool Safety InstructionsAIR Supply and Connections OperationTool Specifications Operating ModesAIR Supply and Connections Filter LubricationLoading the Tool Cold Weather OperationRemoving Nails Fastener Depth Control AdjustmentTo Adjust the Fastener Depth Control Tool OperationSequential Trip Operation OperationContact Trip Operation Tool Operation Check AIR SUPPLY-PRESSURE and Volume Replacement PartsAssembly Procedure for Seals Maintaining the Pneumatic ToolAvailable Accessories Trouble Shooting Problem Cause CorrectionÍndice IntroducciónNota AL Cargar LA Herramienta Instrucciones DE SeguridadSuministro DE Aire Y Conexiones OperaciónEspecificaciones DE LA Herramienta Mantenimiento DE LA HerramientaModos DE Operación Suministro DE Airey Conexiones Filtro LubricaciónCarga DE LAS Herramientas Funcionamiento EN Clima FríoOperación DE LA Herramienta Ajuste DEL Control DE Profundidad DEL ClavoExtracción DE Clavos Para Ajustar EL Control DE Profundidad DEL ClavoOperación DEL Disparo Secuential OperaciónAntes DE Manejar U Operar Esta Herramienta Operación DEL Disparo DE ContactoFuncionamiento DEL Disparo Secuencial Operación DE LA Herramienta ContinuaciónRevisión Funcional DE LA Herramienta Funcionamiento DEL Disparo DE ContactoPiezas DE Repuesto Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Procedimiento DE Ensamblaje Para LOS SellosAccesorios Disponibles Solución DE Problemas El vástago de la válvula de disparo Tiene fuga de aireRemarque Garantie Limitée É.-U. et Canada seulementChargement DE L’APPAREIL Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement FonctionnementCaractéristiquestechniques DES Outils Modes DE FonctionnementAlimentation EN AIR ET Connexions Filtre LubrificationFonctionnement EN Basse Température Fonctionnement DE L’OUTIL Commande DE Réglage DE Profondeur DE FixationPour Régler LA Profondeur DE Fixation Fonctionnement DE L’OUTIL Suite Fonctionnement EN Mode Déclenchement SéquentielFonctionnement Fonctionnement PAR Déclenchement SUR ContactMaintenance DE L’OUTIL Pneumatique Vérification DE L’ÉTAT DE Marche DE L’OUTILAccessoires Offerts Dépannage Vérifiez l’équipement d’alimentation d’air
Related manuals
Manual 37 pages 57.02 Kb