Hitachi N 5008AC manual Methods of Operation

Page 12

English

⬤Never place your hands or feet closer than 8 inches (200 mm) from firing head when using.

⬤Do not drive staples on top of other staples or with Stapler at too steep of an angle; staples can ricochet and hurt someone.

⬤In order to avoid double fire or unwanted ejection of a staple due to bouncing of the Stapler.

1)do not push Stapler on workpiece with strong force;

2)take Stapler away from workpiece using recoil;

3)release trigger quickly when performing trigger fire.

⬤Do not drive staples into thin boards or near corners and edges of workpiece. Staples can be driven through or away from workpiece and hit someone.

⬤Never drive staples from both sides of a wall at the same time. Staples can be driven into and through the wall and hit a person on the opposite side.

⬤Never use Stapler which is defective or operating abnormally.

⬤Do not use Stapler as hammer.

⬤Disconnect air hose from Stapler when:

1)it is not in use;

2)leaving work area;

3)moving it to another location; and

4)handing it to another person.

This Hitachi Stapler has a STANDARD CONTACT TRIP MECHANISM (Bounce File). An OPTIONAL SEQUENTIAL TRIP MECHANISM kit (SINGLE SHOT) is available as order part number 876762.

THE STANDARD CONTACT TRIP MECHANISM (Bounce Fire) is for use where rapid fastener placement is desired and must be operated in accordance with the following “Methods of Operation”.

METHODS OF OPERATION

This Stapler is equipped with the push lever and does not operate unless the push lever is depressed (upward position).

There are two methods of operation to drive staples with this Stapler.

They are:

1.Intermittent operation (Trigger fire):

2.Continuous operation (Push lever fire):

(1)Intermittent operation (Trigger fire)

1 Position the staple outlet on the workpiece with finger off the trigger.

2 Depress the push lever firmly until it is completely depressed.

3 Pull the trigger to drive a staple.

4 Remove finger from the trigger.

To drive another staple, move the Stapler along the workpiece and repeat this procedure.

Trigger

3

2

Push Lever

(2)Continuous operation (Push lever fire)

1 Pull the trigger with the Stapler off the workpiece. 2 Depress the push lever against the workpiece to

drive a staple.

3 Move the Stapler along the workpiece with a bouncing motion.

Each depression of the push lever will drive a staple.

As soon as the desired number of staples have been driven, remove finger from the trigger.

Previously pull the trigger

1

3

Push Lever

WARNING

⬤Keep your finger off the trigger except during fastening operation, beacuse serious injury could result if the push lever accidentally contacts you or others in work area.

⬤Keep hands and body away from the discharge area. The Stapler with contact trip mechanism may bounce from the recoil of driving a fastener and unwanted subsequent fastener may be driven, possibly causing injury.

⬤Some types of loaded staples can spark out of the muzzle during a nail driving operation. Exercise caution!

— 12 —

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Modèle N 5008AC PeligroContents Definitions of Signal Words Important InformationSafety Check for Live Wires Never USE in Presence of Flammable Liquids or GasesKeep Hands and Feet Away from Firing Head During USE Keep Visitors AwayEMPLOYER’S Responsibilities Operation Name of PartsSpecifications AccessoriesStandard Accessories Optional AccessoriesPower source LubricationTesting the Stapler Cold Weather CareStapler Must not Leak AIR Adjusting AIR Pressure Loading StaplesStapler Operation Stapler Must OperateMethods of Operation Adjusting the Stapling Depth Disconnect AIR Hose from StaplerMaintenance Maintenance and InspectionService and Repairs Disconnect AIR HoseAction WHY HOW Problem Check Method CorrectionDefinition DES Mots DE Signalisation Information ImportanteSecurite AvertissementRanger LE Cloueur Correctement Maintenir L’AIRE DE Travail PropreEloigner LES Visiteurs Porter UN Habillement ApproprieResponsabilites DE L’EMPLOYEUR Utilisation NOM DES PiecesRemarque Accessoires EN Option Accessoires AvertissementAccessoires Standard Selection DES AgrafesAlimentation D’AIR GraissageEntretien PAR Temps Froid Essai DE L’AGRAFEUSE’AGRAFEUSE NE Doit PAS Fonctionner Reglage DE LA Pression D’AIR Avertissement Chargement DES Agrafes AvertissementUtilisation DE L’AGRAFEUSE ’AGRAFEUSE Doit FonctionnerMethodes D’UTILISATION Reglage DE LA Profondeur DE Agrafage Debrancher LE Tuyau D’AIR DE LagrafeuseToujours Porter DES Lunettes DE PROTEC- Tion Entretien Entretien ET InspectionEntretien ET Reparations Avertissement Débrancher LE Tuyau D’AIRProbleme Verification Correction Action Pourquoi CommentInformación Importante Definición DE LAS Palabras ClaveSeguridad AdvertenciaMantenga a LOS Visitantes Alejados 11. Vístase AdecuadamenteNo Utilice Nunca UN Acoplador SIN Descarga CON LA Grapadora Compruebe LA Palanca DE Empuje Antes DE LA UtilizaciónResponsabilidades DEL Empresario Operación NomenclaturaEspecificaciones Selección DE GrapasAccesorios Opcionales AplicacionesSuministro DE Aire Peligro Fuente de propulsiónLubricación Cuidados Para Climas FríosPrecaución Prueba DE LA Grapadora PeligroAjuste DE LA Presión DE Aire Advertencia Carga DE Grapas AdvertenciaLA Grapadora Deberá Funcionar LA Grapadora Deberá Funcionar AdecuadamentePrecaucion Operación DE LA GrapadoraMétodos DE Operación Ajuste DE LA Profundidad DE Grapado Desconecte LA Manguera DE Aire DE LA GrapadoraUtilice Siempre Gafas Protectoras Para LOS Ojos Mantenimiento Mantenimiento E InspecciónServicio Y Reparaciones Advertencia Desconecte LA Manguera DE AireProblema Méthodo DE Comprobación Solución Acción Para CómoPage Hitachi Koki Canada Co

N 5008AC specifications

The Hitachi N 5008AC is an advanced horizontal machining center specifically designed to meet the demands of precision milling and heavy-duty machining operations. This cutting-edge machine reflects Hitachi's commitment to innovation and quality in manufacturing, catering to a wide range of industries including automotive, aerospace, mold and die, and general machining.

One of the key features of the N 5008AC is its robust construction. The machine incorporates a solid, reinforced casting design to minimize vibration, ensuring high stability during complex machining tasks. This structural integrity contributes to improved accuracy and surface finish, making it ideal for intricate components that require tight tolerances.

The N 5008AC is powered by a high-performance spindle that reaches speeds of up to 12,000 RPM. This spindle is equipped with an advanced cooling system which aids in maintaining thermal stability, thereby enhancing performance during prolonged machining operations. Coupled with a powerful servo motor, it provides higher torque at low speeds, making it suitable for both high-speed and heavy-duty applications.

Another notable aspect of the N 5008AC is its intelligent control system that leverages cutting-edge CNC technology. The system features advanced programming capabilities, enabling users to achieve complex multi-axis machining operations with ease. Its user-friendly interface simplifies the setup process, allowing operators to efficiently switch between different tasks and optimize machining time.

The machine also comes with a generous tool magazine that can accommodate a wide range of tooling options, promoting flexibility and efficiency. With an automatic tool changer, the N 5008AC minimizes downtime during tool swaps, maximizing productivity. Additionally, with a large work envelope, this machining center is adept at handling sizable workpieces.

In terms of technologies, the N 5008AC utilizes adaptive control features that adjust machining parameters in real-time based on cutting conditions. This smart technology not only enhances machining accuracy but also extends tool life by ensuring optimal cutting conditions throughout the machining process.

Moreover, the N 5008AC emphasizes energy efficiency, incorporating systems that reduce power consumption while maintaining peak performance. This commitment to sustainability aligns with global trends towards environmentally responsible manufacturing practices.

In summary, the Hitachi N 5008AC stands out as a versatile and powerful machining center that combines exceptional stability, advanced CNC technology, and a host of intelligent features, making it a top choice for manufacturers aiming to enhance productivity and precision.
Top Page Image Contents