DeWalt D25851K Active Vibration Control Fig, Inserting and Removing Spline Drive Accessories Fig

Page 34

English

FIG. 2

M

FIG. 3

I

 

 

 

K

 

 

 

N O

P L

J

H

C

C

TO MOUNT IN FRONT POSITION (FIG. 2)

1.Unscrew the side handle (C) and disassemble the side handle clamp (J).

2.Snap the steel ring (K) over the collar (L) behind the tool holder

(M). Squeeze both ends of the steel ring together. Mount the bushing (N) and insert the pin (O).

3.Slide the side handle clamp (J) over the bushing and screw on the clamp knob (H) –do not tighten.

4.Screw the side handle (C) into the clamp knob (H) and tighten.

5.Rotate the side handle mounting assembly to the desired position. For hammerdrilling horizontally with a heavy drill bit, place the side handle assembly at an angle of approximately 20° to the tool for optimum control.

6.Lock the side handle mounting assembly in place by tightening the clamp knob (H).

TO MOUNT IN REAR POSITION (FIG. 3)

1.Unscrew the side handle (C) and remove it from the side handle mounting assembly. Leave the side handle mounting assembly in the front position.

2.Screw the side handle directly into one of the rear side handle positions (I) on either side of the tool.

Active Vibration Control (Fig. 1)

D25602, D25831, D25851

For best vibration control, hold the tool with one hand on the main handle (D) and the other hand on the side handle (C). Apply just enough pressure so the damping device on the main handle is approximately midstroke. The hammer only needs enough pressure to engage the active vibraton control. Applying too much pressure will not make the tool drill or chip faster and active vibration control will not engage.

Inserting and Removing Spline Drive Accessories (Fig. 4)

D25851

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories.

1.Insert the bit shank into the tool holder (M) as far as it will go. The groove on the chisel shank (Q) must be aligned with the symbol

(R) on the toolholder. If inserted correctly, the locking sleeve (P) moves back to the end position and shows a closed lock symbol.

2.Pull on the bit to be sure that it is properly locked.

32

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Page Page Seguridad DEL Área DE Trabajo Definiciones Normas De seguridadSeguridad Eléctrica Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaMantenimiento Longitud del cable en metros m Corriente Sección nominal mínima del cable en NominalUSO Previsto MotorDescripción FIG D25501, D25601, D25602D25602 D25820, D25831, D25851 Montaje Y AjustesMango lateral Fig Montaje EN LA Posición Delantera FIGD25602, D25831, D25851 Control activo de la vibración FigMontaje EN LA Posición Trasera FIG D25851Control completo del par de torsión Fig Inserción y desmontaje de accesorios SDS Max FigD25501, D25602, D25820, D25831 Luces indicadoras LED Fig Control electrónico de la velocidad y el impacto FigSelector de modo Fig FuncionamientoTaladrado con brocas sólidas Posición Adecuada de las manos FigInterruptor de gatillo Fig Función DE Arranque ProgresivoCincelado Perforación con brocas tipo coronaMantenimiento Reparaciones LubricaciónLimpieza AccesoriosD25820-AR D25501-ARD25602-AR D25831-ARGuarde Estas Instruções Definições diretrizes De segurançaRegras Gerais de Segurança Área DE TrabalhoSegurança Pessoal USO E Cuidados DA FerramentaInstruções de segurança adicionais para marteletes rotativos ReparosTensão Comprimento do cabo de extensão Faixa de Secção mínima do cabo de extensão Corrente nominalUSO Devido DA Ferramenta Descrição FIGD25820, D2583, D25851 Empunhadura lateral Fig Montagem E AjustesComo Instalar NA Posição Frontal FIG Como instalar e retirar acessórios para ranhuras Fig Controle de vibração ativa FigComo Instalar NA Posição Traseira FIG Controle de torque completo Fig Como instalar e retirar acessórios SDS Max FigIndicadores luminosos de alimentação elétrica Fig Controle eletrônico de velocidade e impacto FigSeletor de Modo Fig FuncionamentoMartelamento com uma broca sólida Como segurar corretamente a ferramenta FigGatilho interruptor Fig Função DE Partida SuavePerfuração por percussão com uma broca-coroa RaspagemManutenção D25602-B2 EspecificaçõesD25501-B2 D25820-BR D25831-B2Work Area Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Electrical SafetyPower Tool USE and Care Additional Safety Instructions for Rotary HammersService Rated Ampere Voltage Volts Total length of cord in meters mRange Cord in meters mm Description FIG Side Handle Fig Assembly and AdjustmentsIntended USE To Mount in Front Position FIG Inserting and Removing Spline Drive Accessories FigActive Vibration Control Fig To Mount in Rear Position FIGInserting and Removing SDS Max Accessories Fig Complete Torque Control FigElectronic Speed and Impact Control Fig Mode Selector FigPower Indicator Lights Fig OperationProper Hand Position Fig Trigger Switch FigSoft Start Feature Hammerdrilling with a Solid BitChipping MaintenanceCleaning Repairs LubricationProtecting the Environment AccessoriesMaximum Capacity Specifications Page Page Page Copyright @ 2010, 2013 D Ewalt
Top Page Image Contents