Dremel F013039519 Power Tool Safety Rules, Work Area, Electrical Safety, Personal Safety

Page 2

DM 2610935540 01-07 1/17/07 4:06 PM Page 2

Power Tool Safety Rules

!

WARNING

Read and understand all instructions. Failure to follow all instructions listed below, may

result in electric shock, fire and/or serious personal injury.

 

 

SAVE THESE INSTRUCTIONS

Work Area

power tools may result in serious personal injury.

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep by-standers, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

Double Insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Before plugging in the tool, be certain the outlet voltage supplied is within the voltage marked on the nameplate. Do not use “AC only” rated tools with a DC power supply.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s rubber gloves and footwear will further enhance your personal safety.

Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase

the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock. Refer to “Recommended sizes of Extension Cords” in the Accessory section of this manual.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Keep handles dry, clean and free from oil and grease.

Avoid accidental starting. Be sure switch is “OFF” before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch “ON” invites accidents.

Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

Do not use tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. Any alteration or modification is a misuse and may result in a dangerous condition.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Develop a periodic maintenance schedule for your tool.

Page 2

Image 2
Contents 75th Anniversary F013039519Personal Safety Power Tool Safety RulesElectrical Safety Work AreaSafety Rules for Rotary Tools ServiceSafety Rules for Rotary Tools Symbols Accidentally Functional Description and SpecificationsModel F013039519 Rotary Tool Right Angle Attachment Flex-ShaftCutting Guide Dremel Keyless Chuck AssemblyCollet Identification Chart Shape Wood Carve Wood Deburr Metal Operating InstructionsSharpen Tools Flow and causes the motor to overheat Questions or Problems?CallUsing the Rotary Tool Needs for Slower Speeds Switch SettingOperating Speeds Speed RangeStep Assembly & Operation of AttachmentsInstallation Instructions Step Operating Instructions Collet and Accessory AssemblyCollet Removal and Replacement Disengagement of the Flex-ShaftFor use in drywall Important When viewing the tool from the top, the StepDescription For use on wall tile, cement board and plasterGrout Removal Kit Grout Removal Attachment Cutting Depth AdjustmentTo set cutting depth Cleaning Grout Removing Grout to Replace a Broken TileOperating Instructions Lock button when changing Prolong usageExtension Cords Maintenance InformationCleaning Cord with adequate sizeDremel Attachments Dremel Accessories Sanding Accessories Wire BrushesPolishing Accessories Bristle BrushesTile Cutting Bit Cutting WheelsDrywall Cutting Bit Spiral Cutting BitDM 2610935540 01-07 1/17/07 406 PM Speed for light cuts, caution burning on deep grooves Use only Dremel Tested, High Performance AccessoriesDepending on cutting direction relative to grain Speed Settings Drill BIT Mode demploi de loutil rotatif 75e anniversaire Modèle F013039519Règles de Sécurité Générales AvertissementConsignes de sécurité pour outils rotatifs RéparationConsignes de sécurité pour outils rotatifs suite Le plomb provenant des peintures à base de plombSymboles Description fonctionnelle et spécifications Outil Rotatif modèle F013039519565 Nécessaire Accessoire à angle droitArbre flexible Universel de coupeQue le Outil Rotatif est en marche AssemblageOutil Rotatif avant Mandrin Sans CLÉ DremelConsignes d’utilisation Affûtage des outilsUtilisation du Outil Rotatif Consignes d’utilisation suiteQuestions ou problèmes ? Composez le Plage de vitesses Vitesses de fonctionnementNécessité de vitesses plus lentes Vitesses de fonctionnement suite Assemblage et fonctionnement des accessoiresDirectives D’INSTALLATION Larbre flexibleDébranchement de l’arbre Flex-Shaft Enlèvement et remplacement du morsDirectives D’USAGE Ne tirez pas sur l’arbreLe guide de coupe NE PAS Utiliser SUR LES Carreaux CéramiquesÉlimination du coulis pour remplacer un carreau cassé Kit pour l’extraction de coulisPour régler la profondeur de coupe Nettoyage du coulis Assemblage et Fonctionnement des Accessoires Mode d’emploiAvertissement Il est possible que l’accessoire chauffe lors ’une utilisation prolongéeNettoyage Renseignements sur l’entretienEntretien RallongesAccessoires Dremel Couteaux à grande vitesse DouillesMandrins Couteaux au carbure de tungstèneBrosses métalliques Accessoires de polissageAccessoires de ponçage Brosses en soie de porcAccessoires Dremel suite Avertissement Réglages DE Vitesse Selon le sens de coupe par rapport au grain du boisAcier Réglages DE Vitesse Remarques Canada Garantie limitée de DremelÉTATS-UNIS Modelo F013039519 Normas de seguridad para herramientas mecánicas Conserve Estas InstruccionesNormas de seguridad para herramientas giratorias Normas de seguridad para herramientas giratorias Símbolos De Ni-CdDescripción funcional y especificaciones Herramienta giratoria modelo F013039519Cortadores multiuso Eje flexibleJuego de Accesorio de ángulo rectoMandril DE Apriete SIN Llave Dremel EnsamblajeCuadro DE Identificacion DE Portaherramientas No acople el cierre mientras laDar forma a madera Desbarbar metal Tallar madera Cortar Instrucciones de utilizaciónAfilar herramientas Utilización de la herramienta giratoria ¿Preguntas o problemas? Llame alConsejos de funcionamiento Bloquea el flujo de aire y hace que el motor se recalienteIntervalo de velocidad Velocidades de funcionamientoNecesidades de velocidades más lentas Utilización con brocas de fresadora causará retroceso Montaje y funcionamiento de los aditamentos¡Deje que la velocidad haga el trabajo Instrucciones Para LA InstalaciónEnsamblaje del Mandril y sus Accesorios Instrucciones Para OperarDesenganche del Eje Flexible Desmontaje y Montaje del MandrilNo Para Utilizar CON Cerámica DE Piso Montaje y Funcionamiento de los AccesoriosLa guía de corte Juego para quitar lechada Cómo ajustar la profundidad de corte Al Limpiar LechadaInstrucciones de operación Advertencias de Seguridad para la Remoción de LechadaAditamento en ángulo recto Limpieza Información de mantenimientoServicio Cordones de extensiónJuego para quitar lechada Aditamentos para DremelEje flexible Aditamento de fresadoraAccesorios para la Dremel Accesorios para pulir Cepillos de cerdaPresión de cepillado Ruedas abrasivas de óxido de aluminioBroca de corte en espiral Ruedas de corteBrocas de fresadora de alta velocidad Broca para cortar pared de tipo secoDM 2610935540 01-07 1/17/07 407 PM Posiciones DE Velocidad Ceramica Accesorios Para Pulir Canadá Garantía limitada de DremelEstados Unidos Model Modèle Modelo NO. DE LA Piece Description DescripcionDremel FLEX-SHAFT Attachment NO. DE PièceAngled Cone Housing DM 2610935540 01-07 1/17/07 407 PM Remarques Notas Canada Outside Dremel Limited WarrantyUnited States