Dremel F013039519 owner manual Step Operating Instructions, Disengagement of the Flex-Shaft, Much

Page 13

DM 2610935540 01-07 1/17/07 4:06 PM Page 13

STEP 2

STEP 3

 

 

 

 

 

 

Step 2. Unscrew the housing cap from the tool. Step 3. Remove the collet.

Note: If the collet nut and collet are not removed from the motor shaft, the tool will not function properly.

STEP 4

OPERATING INSTRUCTIONS

Disengagement of the Flex-Shaft

The flexible shaft may become disengaged if the motor of your rotary tool is not elevated higher than the working end of the flex-shaft. The #2222 Rotary Tool Stand is recommended to hold the rotary tool at the proper height.

Collet and Accessory Assembly

The collet assembly consists of a collet nut and collet. Take the collet nut and collet that were removed from your tool in step 2 and 3 and insert them into the tip of the flex-shaft handpiece.

Step 4. Install the driver cap on the motor shaft and tighten.

! CAUTION

To prevent damage to tool, do not

 

overtighten driver cap. Tighten

 

the driver cap finger tight and then tighten an additional 1/3 turn with the wrench. (Wrench included with your rotary tool kit)

STEP 5

Step 5. Attach by screwing the collar of the flex-shaft to the rotary tool. Make sure the square end of the center core engages the square hole socket in the driver cap.

! CAUTION

Do not pull out center core to

 

engage into driver cap. This

 

could cause disengagement of center core from handpiece. If tool stops when shaft is bent, center core may be lodged in driver cap. Loosen shaft and remove core from driver cap. Then screw flexible shaft onto rotary tool housing again.

Insert an accessory or bit as deeply as possible to avoid wobble during use. With the shaft lock button engaged on the flex-shaft handpiece retighten the collet nut.

Collet Removal and Replacement

Four different size collets to accommodate different shank sizes, are sold separately for your flex-shaft. To install a different collet, remove the collet nut and remove the old collet. Insert the unslotted end of the collet in the hole in the end of the flex-shaft. Replace collet nut on the shaft. Always use the collet which matches the shank size of the accessory you plan to use. Never force a larger diameter shank into a collet.

FLEXIBLE SHAFT LUBRICATION — The flexible shaft should be lubricated after every 25-30 hours of use. To lubricate, unscrew the flexible shaft assembly from the motor housing. Pull the center core out of the flexible shaft assembly. Wipe a very thin film of a good quality, high temperature grease on to the center core.

! CAUTION

To prevent damage to tool

do not

 

over grease shaft. Too

much

 

grease will cause the unit to overheat. Dremel shaft lubricant No. 5990952 or automotive wheel bearing grease should be used.

Reattach the flex-shaft to the rotary tool.

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents F013039519 75th AnniversaryElectrical Safety Power Tool Safety RulesPersonal Safety Work AreaService Safety Rules for Rotary ToolsSafety Rules for Rotary Tools Symbols Model F013039519 Rotary Tool Functional Description and SpecificationsAccidentally Cutting Guide Flex-ShaftRight Angle Attachment Collet Identification Chart AssemblyDremel Keyless Chuck Sharpen Tools Operating InstructionsShape Wood Carve Wood Deburr Metal Using the Rotary Tool Questions or Problems?CallFlow and causes the motor to overheat Operating Speeds Switch SettingNeeds for Slower Speeds Speed RangeInstallation Instructions Assembly & Operation of AttachmentsStep Collet Removal and Replacement Collet and Accessory AssemblyStep Operating Instructions Disengagement of the Flex-ShaftDescription Important When viewing the tool from the top, the StepFor use in drywall For use on wall tile, cement board and plasterTo set cutting depth Cleaning Grout Grout Removal Attachment Cutting Depth AdjustmentGrout Removal Kit Removing Grout to Replace a Broken TileOperating Instructions Prolong usage Lock button when changingCleaning Maintenance InformationExtension Cords Cord with adequate sizeDremel Attachments Dremel Accessories Polishing Accessories Wire BrushesSanding Accessories Bristle BrushesDrywall Cutting Bit Cutting WheelsTile Cutting Bit Spiral Cutting BitDM 2610935540 01-07 1/17/07 406 PM Depending on cutting direction relative to grain Use only Dremel Tested, High Performance AccessoriesSpeed for light cuts, caution burning on deep grooves Speed Settings Drill BIT Modèle F013039519 Mode demploi de loutil rotatif 75e anniversaireAvertissement Règles de Sécurité GénéralesRéparation Consignes de sécurité pour outils rotatifsLe plomb provenant des peintures à base de plomb Consignes de sécurité pour outils rotatifs suiteSymboles Outil Rotatif modèle F013039519 Description fonctionnelle et spécificationsArbre flexible Accessoire à angle droit565 Nécessaire Universel de coupeOutil Rotatif avant AssemblageQue le Outil Rotatif est en marche Mandrin Sans CLÉ DremelAffûtage des outils Consignes d’utilisationQuestions ou problèmes ? Composez le Consignes d’utilisation suiteUtilisation du Outil Rotatif Nécessité de vitesses plus lentes Vitesses de fonctionnementPlage de vitesses Directives D’INSTALLATION Assemblage et fonctionnement des accessoiresVitesses de fonctionnement suite Larbre flexibleDirectives D’USAGE Enlèvement et remplacement du morsDébranchement de l’arbre Flex-Shaft Ne tirez pas sur l’arbreNE PAS Utiliser SUR LES Carreaux Céramiques Le guide de coupePour régler la profondeur de coupe Nettoyage du coulis Kit pour l’extraction de coulisÉlimination du coulis pour remplacer un carreau cassé Mode d’emploi Assemblage et Fonctionnement des Accessoires’une utilisation prolongée Avertissement Il est possible que l’accessoire chauffe lorsEntretien Renseignements sur l’entretienNettoyage RallongesAccessoires Dremel Mandrins DouillesCouteaux à grande vitesse Couteaux au carbure de tungstèneAccessoires de ponçage Accessoires de polissageBrosses métalliques Brosses en soie de porcAccessoires Dremel suite Avertissement Selon le sens de coupe par rapport au grain du bois Réglages DE VitesseAcier Réglages DE Vitesse Remarques ÉTATS-UNIS Garantie limitée de DremelCanada Modelo F013039519 Conserve Estas Instrucciones Normas de seguridad para herramientas mecánicasNormas de seguridad para herramientas giratorias Normas de seguridad para herramientas giratorias De Ni-Cd SímbolosHerramienta giratoria modelo F013039519 Descripción funcional y especificacionesJuego de Eje flexibleCortadores multiuso Accesorio de ángulo rectoCuadro DE Identificacion DE Portaherramientas EnsamblajeMandril DE Apriete SIN Llave Dremel No acople el cierre mientras laAfilar herramientas Instrucciones de utilizaciónDar forma a madera Desbarbar metal Tallar madera Cortar Consejos de funcionamiento ¿Preguntas o problemas? Llame alUtilización de la herramienta giratoria Bloquea el flujo de aire y hace que el motor se recalienteNecesidades de velocidades más lentas Velocidades de funcionamientoIntervalo de velocidad ¡Deje que la velocidad haga el trabajo Montaje y funcionamiento de los aditamentosUtilización con brocas de fresadora causará retroceso Instrucciones Para LA InstalaciónDesenganche del Eje Flexible Instrucciones Para OperarEnsamblaje del Mandril y sus Accesorios Desmontaje y Montaje del MandrilLa guía de corte Montaje y Funcionamiento de los AccesoriosNo Para Utilizar CON Cerámica DE Piso Cómo ajustar la profundidad de corte Al Limpiar Lechada Juego para quitar lechadaAdvertencias de Seguridad para la Remoción de Lechada Instrucciones de operaciónAditamento en ángulo recto Servicio Información de mantenimientoLimpieza Cordones de extensiónEje flexible Aditamentos para DremelJuego para quitar lechada Aditamento de fresadoraAccesorios para la Dremel Presión de cepillado Cepillos de cerdaAccesorios para pulir Ruedas abrasivas de óxido de aluminioBrocas de fresadora de alta velocidad Ruedas de corteBroca de corte en espiral Broca para cortar pared de tipo secoDM 2610935540 01-07 1/17/07 407 PM Posiciones DE Velocidad Ceramica Accesorios Para Pulir Estados Unidos Garantía limitada de DremelCanadá Model Modèle Modelo Description Descripcion NO. DE LA PieceNO. DE Pièce Dremel FLEX-SHAFT AttachmentAngled Cone Housing DM 2610935540 01-07 1/17/07 407 PM Remarques Notas United States Dremel Limited WarrantyCanada Outside
Top Page Image Contents