Dremel F013039519 Wire Brushes, Bristle Brushes, Brushing Pressure, Polishing Accessories

Page 21

DM 2610935540 01-07 1/17/07 4:06 PM Page 21

Wire Brushes

Three different shapes of wire brushes are available.

Never use wire brushes at speeds greater than 15,000 RPM. Refer to Operating Speeds section for proper tool speed setting. The three shapes come in three different materials: stainless steel, brass and carbon wire. The stainless steel perform well on pewter, aluminum, stainless steel, and other metals, without leaving "after-rust". Brass brushes are non sparking, and softer than steel; making them good for use on soft metal like gold, cooper and brass. The carbon wire brushes are good for general purpose cleaning.

Bristle Brushes

These are excellent cleaning tools on silverware, jew- elry and antiques. The three shapes make it possible to get into tight corners and other difficult places. Bristle brushes can be used with polishing compound for faster cleaning or polishing.

Brushing Pressure

1.Remember, the tips of a wire brush do the work. Operate the brush with the lightest pressure so only the tips of the wire come in contact with the work.

2.If heavier pressures are used, the wires will be overstressed, resulting in a wiping action; and if this is continued, the life of the brush will be shortened due to wire fatigue.

3.Apply the brush to the work in such a way that as much of the brush face as possible is in full contact with the work. Applying the side or edge of the brush to the work will result in wire breakage and shortened brush life.

CORRECT:

Wire tips doing the work.

15°

INCORRECT:

Excessive pressure can cause wire breakage.

Polishing Accessories

These include an impregnated polishing point and an impregnated polishing wheel for bringing metal sur- faces to smooth finish; a felt polishing tip and felt polishing wheel, and cloth polishing wheel, all used for polishing plastics, metals, jewelry and small parts. Also included in this group is a polishing compound (No. 421) for use with the felt and cloth polishers.

Polishing points make a very smooth surface, but a high luster is obtained using felt or cloth wheels and polishing compound. For best results polishing accessories should be used at speeds not greater than 15,000 RPM. Refer to Operating Speeds section for proper tool speed setting.

No polishing compound is needed when using the 425 Polishing Wheel or 427 Polishing point.

Aluminum Oxide Abrasive Wheels

Use to remove paint, deburr metal, polish stainless steel and other metals. Available in fine and medium grits. 1/8" shank.

Sanding Accessories

Sanding discs in fine, medium and coarse grades are made to fit mandrel No. 402. They can be used for nearly any small sanding job you might have, from model making to fine furniture finishing. In addition, there is the drum sander, a tiny drum which fits into the Rotary Tool and makes it possible to shape wood, smooth fiberglass, sand inside curves and other diffi- cult places, and other sanding jobs. You replace the sanding bands on the drum as they become worn and lose their grit. Bands come in fine and coarse grades. Flapwheels grind and polish flat or contoured surfaces. They are used most effectively as a finishing sander after heavier surface sanding and material removal is completed. Flapwheels come in fine and coarse grades. Buffs are a great finishing accessory for cleaning and light sanding. They work effectively on metal, glass, wood, aluminum and plastics. Coarse and medium buffs are sold together. 1/8" shank.

Grinding Wheel

Use for deburring, removing rust, and general purpose grinding. Use with Mandrel #402.

Page 21

Image 21
Contents F013039519 75th AnniversaryElectrical Safety Power Tool Safety RulesPersonal Safety Work AreaService Safety Rules for Rotary ToolsSafety Rules for Rotary Tools Symbols Functional Description and Specifications Model F013039519 Rotary ToolAccidentally Flex-Shaft Cutting GuideRight Angle Attachment Assembly Collet Identification ChartDremel Keyless Chuck Operating Instructions Sharpen ToolsShape Wood Carve Wood Deburr Metal Questions or Problems?Call Using the Rotary ToolFlow and causes the motor to overheat Operating Speeds Switch SettingNeeds for Slower Speeds Speed RangeAssembly & Operation of Attachments Installation InstructionsStep Collet Removal and Replacement Collet and Accessory AssemblyStep Operating Instructions Disengagement of the Flex-ShaftDescription Important When viewing the tool from the top, the StepFor use in drywall For use on wall tile, cement board and plasterTo set cutting depth Cleaning Grout Grout Removal Attachment Cutting Depth AdjustmentGrout Removal Kit Removing Grout to Replace a Broken TileOperating Instructions Prolong usage Lock button when changingCleaning Maintenance InformationExtension Cords Cord with adequate sizeDremel Attachments Dremel Accessories Polishing Accessories Wire BrushesSanding Accessories Bristle BrushesDrywall Cutting Bit Cutting WheelsTile Cutting Bit Spiral Cutting BitDM 2610935540 01-07 1/17/07 406 PM Use only Dremel Tested, High Performance Accessories Depending on cutting direction relative to grainSpeed for light cuts, caution burning on deep grooves Speed Settings Drill BIT Modèle F013039519 Mode demploi de loutil rotatif 75e anniversaireAvertissement Règles de Sécurité GénéralesRéparation Consignes de sécurité pour outils rotatifsLe plomb provenant des peintures à base de plomb Consignes de sécurité pour outils rotatifs suiteSymboles Outil Rotatif modèle F013039519 Description fonctionnelle et spécificationsArbre flexible Accessoire à angle droit565 Nécessaire Universel de coupeOutil Rotatif avant AssemblageQue le Outil Rotatif est en marche Mandrin Sans CLÉ DremelAffûtage des outils Consignes d’utilisationConsignes d’utilisation suite Questions ou problèmes ? Composez leUtilisation du Outil Rotatif Vitesses de fonctionnement Nécessité de vitesses plus lentesPlage de vitesses Directives D’INSTALLATION Assemblage et fonctionnement des accessoiresVitesses de fonctionnement suite Larbre flexibleDirectives D’USAGE Enlèvement et remplacement du morsDébranchement de l’arbre Flex-Shaft Ne tirez pas sur l’arbreNE PAS Utiliser SUR LES Carreaux Céramiques Le guide de coupeKit pour l’extraction de coulis Pour régler la profondeur de coupe Nettoyage du coulisÉlimination du coulis pour remplacer un carreau cassé Mode d’emploi Assemblage et Fonctionnement des Accessoires’une utilisation prolongée Avertissement Il est possible que l’accessoire chauffe lorsEntretien Renseignements sur l’entretienNettoyage RallongesAccessoires Dremel Mandrins DouillesCouteaux à grande vitesse Couteaux au carbure de tungstèneAccessoires de ponçage Accessoires de polissageBrosses métalliques Brosses en soie de porcAccessoires Dremel suite Avertissement Selon le sens de coupe par rapport au grain du bois Réglages DE VitesseAcier Réglages DE Vitesse Remarques Garantie limitée de Dremel ÉTATS-UNISCanada Modelo F013039519 Conserve Estas Instrucciones Normas de seguridad para herramientas mecánicasNormas de seguridad para herramientas giratorias Normas de seguridad para herramientas giratorias De Ni-Cd SímbolosHerramienta giratoria modelo F013039519 Descripción funcional y especificacionesJuego de Eje flexibleCortadores multiuso Accesorio de ángulo rectoCuadro DE Identificacion DE Portaherramientas EnsamblajeMandril DE Apriete SIN Llave Dremel No acople el cierre mientras laInstrucciones de utilización Afilar herramientasDar forma a madera Desbarbar metal Tallar madera Cortar Consejos de funcionamiento ¿Preguntas o problemas? Llame alUtilización de la herramienta giratoria Bloquea el flujo de aire y hace que el motor se recalienteVelocidades de funcionamiento Necesidades de velocidades más lentasIntervalo de velocidad ¡Deje que la velocidad haga el trabajo Montaje y funcionamiento de los aditamentosUtilización con brocas de fresadora causará retroceso Instrucciones Para LA InstalaciónDesenganche del Eje Flexible Instrucciones Para OperarEnsamblaje del Mandril y sus Accesorios Desmontaje y Montaje del MandrilMontaje y Funcionamiento de los Accesorios La guía de corteNo Para Utilizar CON Cerámica DE Piso Cómo ajustar la profundidad de corte Al Limpiar Lechada Juego para quitar lechadaAdvertencias de Seguridad para la Remoción de Lechada Instrucciones de operaciónAditamento en ángulo recto Servicio Información de mantenimientoLimpieza Cordones de extensiónEje flexible Aditamentos para DremelJuego para quitar lechada Aditamento de fresadoraAccesorios para la Dremel Presión de cepillado Cepillos de cerdaAccesorios para pulir Ruedas abrasivas de óxido de aluminioBrocas de fresadora de alta velocidad Ruedas de corteBroca de corte en espiral Broca para cortar pared de tipo secoDM 2610935540 01-07 1/17/07 407 PM Posiciones DE Velocidad Ceramica Accesorios Para Pulir Garantía limitada de Dremel Estados UnidosCanadá Model Modèle Modelo Description Descripcion NO. DE LA PieceNO. DE Pièce Dremel FLEX-SHAFT AttachmentAngled Cone Housing DM 2610935540 01-07 1/17/07 407 PM Remarques Notas Dremel Limited Warranty United StatesCanada Outside