Epson D28402R LOCK-ON Button D28402, On button J. The tool will continue to, Spindle Lock

Page 10

English

SLIDER SWITCH (D28110, D28112)

CAUTION: Before connecting the tool to a power supply, be sure the switch is in the off position by pressing the rear part of the switch and releasing. Ensure the switch is in the off position as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure. If the switch is locked on

when the power is connected, the tool will start unexpectedly.

 

To start the tool, slide the ON/OFF

 

switch (L) toward the front of the tool.

 

To stop the tool, release the ON/OFF

 

switch.

 

For continuous operation, slide the

 

switch toward the front of the tool and

L

press the forward part of the switch

 

inward. To stop the tool while operat-

 

ing in continuous mode, press the rear part of the switch and release.

LOCK-ON BUTTON (D28402)

 

 

 

The lock-on button (J) offers increased

 

 

 

comfort in extended use applications.

 

 

 

To lock the tool on, push the lock-off

 

 

 

lever (B) toward the back of the tool

 

 

 

then depress the paddle switch (A).

 

 

 

With the tool running, depress the lock-

A

B

J

on button (J). The tool will continue to

 

 

 

 

run after the paddle switch is released. To unlock the tool, depress and release the paddle switch. This will cause the tool to stop.

CAUTION: Allow the tool to reach full speed before touching tool to the work surface. Lift the tool from the work surface before turn- ing the tool off.

SPINDLE LOCK

The spindle lock (C) is provided to prevent the spindle from rotat- ing when installing or removing wheels. Operate the spindle lock

only when the tool is turned off, unplugged C from the power supply, and has come to a complete stop. Do not engage the spindle lock while the tool is operating because damage to the tool will result. To engage the lock, depress the spindle lock button and rotate the spindle until you are unable to rotate the spindle further.

Mounting and Using Depressed Center

Grinding Wheels and Sanding

Flap Discs

MOUNTING AND REMOVING HUBBED WHEELS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, depress and release the paddle switch to ensure that the tool is off.

Hubbed wheels install directly on the 5/8"-11 threaded spindle. Thread of accessory must match thread of spindle.

1.Backing flange is retained to the grinder by an O-ring on the spindle. Remove backing flange by pulling and twisting flange away form the machine.

2.Thread the wheel on the spindle by hand.

3.Depress the spindle lock button and use a wrench to tighten the hub of the wheel.

4.Reverse the above procedure to remove the wheel.

CAUTION: Failure to properly seat the wheel before turning the tool on may result in damage to the tool or the wheel.

MOUNTING NON-HUBBED WHEELS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Guide Dutilisation Manual DE Instrucciones Electrical Safety General Safety Rules For All ToolsWork Area Service Additional Specific Safety Instructions for GrindersPersonal Safety Tool USE and CareAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of KickbackComponents Fig Spindle Lock Button Dust Ejection System Spindle not shownRotating the Gear Case Assembly and AdjustmentsAccessories Attaching Side HandleType 27 depressed Center wheel Threaded clamp nut 2 Grinding Wheels Wire WheelsMounting Guard Mounting and Removing Guard D28112, D28402, D28402NSanding Discs 2 Sanding Flap Discs Guards and Flanges SwitchesOperation Mounting and Removing GuardSpindle Lock LOCK-ON Button D28402On button J. The tool will continue to Mounting and Removing Hubbed WheelsBack motion to avoid creating Must be used with included flanges. SeeSurface Grinding with Grinding Wheels Edge Grinding with Grinding WheelsMounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Very Fine FinishingMounting Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting Closed Type 1 Guard Mounting and Using Cutting Type 1 WheelsMounting Cutting Wheels Accessories Three Year Limited Warranty MaintenanceCleaning LubricationYear Free Service Addition to the warranty, Dewalt tools are covered by ourDAY Money Back Guarantee Aire DE Travail Règles de sécurité GénéralitésConserver CES Directives Mesures DE Sécurité ÉlectricitéSécurité Personnelle Utilisation ET Entretien DE L’OUTILDirectives de sécurité supplémentaires pour meuleuses EntretienCauses de l’effet de rebond et prévention de l’opérateur D28402 D28402N D28110 D28112 Positionnement du carter d’engrenages Composants figAssemblage ET Réglages Fixation DE LA Poignée LatéraleMontage du dispositif de protection AccessoiresOuvert, tourner le dispositif I dans la Dispositif de Montage ET Démontage DU Dispositif DE Protection D28110La meuleuse avec un dispositif de protection desserré FonctionnementDispositifs de protection et brides Alignées, puis tirer sur le dispositif de protectionBouton DE Verrouillage D28402 InterrupteursInterrupteur À Palette D28402 D28402N Interrupteur Coulissant D28110, D28112Montage DE Meules Sans Moyeu Dispositif DE Verrouillage DE LA BrocheMontage ET Démontage DE Meules À Moyeu Poser la bride tournante sur collet battuMeulage DE Finition Avec DES Meules Meulage DE Bordure Avec DES MeulesUtilisation DES Patins DE Ponçage ET D’APPUI Finition DE Surface Avec DES Disques À Lamelles DE PonçageMontage DES Patins D’APPUI ET DE Ponçage De la pièce Métalliques ou de brosses métalliques à touretMontage et utilisation de meules de coupe type Montage D’UN Dispositif DE Protection Fermé TypeMontage DE Meules DE Coupe EntretienNettoyage Utilisation DES Meules DE CoupeGarantie limitée de trois ans LubrificationRéparations Contrat D’ENTRETIEN Gratuit D’UN ANÁrea DE Trabajo Instrucciones de seguridad generalesConserve Estas Instrucciones Seguridad EléctricaSeguridad Personal MásCalibre del cordón AWG No recomendado USO Y Cuidados DE LA HerramientaServicio Causas del retroceso y su prevención por parte del operador D28402 D28402N D28110 D28112 Como girar la caja de engranajes Componentes FigEnsamblado Y Ajustes AccesoriosInstalación del protector Montaje Y Remoción DEL Protector D28110Operación Protectores y bridasInterruptores Interruptor DE Paleta D28402, D28402NBloqueo DEL EJE Interruptor Deslizante D28110, D28112Botón DE Bloqueo D28402 Montaje Y Remoción DE Discos CON CuboEnsamblado DE Discos SIN Cubo Esmerilado DE Superficies CON Discos Para EsmerilarDe aplicarla a la superficie de trabajo Esmerilado DE Bordes CON Discos Para EsmerilarAcabado DE Superficies CON Discos Para Lijar Mienta hacia adelante y hacia atrásMontaje y uso de cepillos de alambre y discos de alambre USO DE Almohadillas DE Respaldo Para LijarMontaje y uso de los discos de corte Tipo La sección elevada piloto Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte Piloto en dirección opuesta al discoLubricación MantenimientoLimpieza ReparacionesAÑO DE Servicio Gratuito Garantía limitada por tres añosExcepciones Garantía DE Reembolso DE SU Dinero POR 90 DíasCULIACAN, SIN Especificaciones D28402, D28402N
Top Page Image Contents