Epson D28112, D28402R instruction manual Sanding Discs 2 Sanding Flap Discs

Page 8

4-1/2" Cutting Wheels

Sanding Discs

4-1/2" Sanding Flap Discs

English

Type 1 guard

backing flange

abrasive cutting wheel

clamp nut

Type 1 guard

backing flange

diamond cutting wheel

clamp nut

rubber backing pad

sanding disc

threaded clamp nut

Type 27 guard

hubbed sanding

flap disc

Type 27 guard

backing flange

non-hubbed sanding

flap disc

threaded clamp nut

1.	Open the guard latch (M). Align
1.	Open the guard latch (M). Align	N
	the lugs (N) on the guard with the
	the lugs (N) on the guard with the
	slots (O) on the gear case.
2.	Push the guard down until the
	guard lugs engage and rotate	O
	freely in the groove on the gear	O
	case hub.		M

3.With the guard latch open, rotate

the guard (I) into the desired working po sition. The guard body should be posi- tioned between the spindle and the operator to provide maximum operator protection.

4.Close the guard latch to secure the guard on the gear case. You should not be able to rotate the guard by hand when the

latch is closed. Do not operate the grinder with a loose guard or the clamp lever in open position.

5. To remove the guard, open the guard latch, rotate the guard so that the arrows are aligned and pull up on the guard.

NOTE: The guard is pre-adjusted to the diameter of the gear case hub at the factory.

If, after a period of time, the guard becomes P loose, tighten the adjusting screw (P) with clamp lever in the closed position.

I

7

Image 8

Contents Guide Dutilisation Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety Additional Specific Safety Instructions for Grinders Personal SafetyService Tool USE and CareAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of KickbackComponents Fig Spindle Lock Button Dust Ejection System Spindle not shownAssembly and Adjustments AccessoriesRotating the Gear Case Attaching Side Handle2 Grinding Wheels Wire Wheels Mounting GuardType 27 depressed Center wheel Threaded clamp nut Mounting and Removing Guard D28112, D28402, D28402NSanding Discs 2 Sanding Flap Discs Switches OperationGuards and Flanges Mounting and Removing GuardLOCK-ON Button D28402 On button J. The tool will continue toSpindle Lock Mounting and Removing Hubbed WheelsMust be used with included flanges. See Surface Grinding with Grinding WheelsBack motion to avoid creating Edge Grinding with Grinding WheelsUsing Sanding Backing Pads Surface Finishing with Sanding Flap DiscsMounting Sanding Backing Pads Very Fine FinishingUsing Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Mounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Maintenance CleaningAccessories Three Year Limited Warranty LubricationDAY Money Back Guarantee Addition to the warranty, Dewalt tools are covered by ourYear Free Service Règles de sécurité Généralités Conserver CES DirectivesAire DE Travail Mesures DE Sécurité ÉlectricitéSécurité Personnelle Utilisation ET Entretien DE L’OUTILDirectives de sécurité supplémentaires pour meuleuses EntretienCauses de l’effet de rebond et prévention de l’opérateur D28402 D28402N D28110 D28112 Composants fig Assemblage ET RéglagesPositionnement du carter d’engrenages Fixation DE LA Poignée LatéraleOuvert, tourner le dispositif I dans la AccessoiresMontage du dispositif de protection Dispositif de Montage ET Démontage DU Dispositif DE Protection D28110Fonctionnement Dispositifs de protection et bridesLa meuleuse avec un dispositif de protection desserré Alignées, puis tirer sur le dispositif de protectionInterrupteurs Interrupteur À Palette D28402 D28402NBouton DE Verrouillage D28402 Interrupteur Coulissant D28110, D28112Dispositif DE Verrouillage DE LA Broche Montage ET Démontage DE Meules À MoyeuMontage DE Meules Sans Moyeu Poser la bride tournante sur collet battuMeulage DE Finition Avec DES Meules Meulage DE Bordure Avec DES MeulesMontage DES Patins D’APPUI ET DE Ponçage Finition DE Surface Avec DES Disques À Lamelles DE PonçageUtilisation DES Patins DE Ponçage ET D’APPUI De la pièce Métalliques ou de brosses métalliques à touretMontage et utilisation de meules de coupe type Montage D’UN Dispositif DE Protection Fermé TypeEntretien NettoyageMontage DE Meules DE Coupe Utilisation DES Meules DE CoupeLubrification RéparationsGarantie limitée de trois ans Contrat D’ENTRETIEN Gratuit D’UN ANInstrucciones de seguridad generales Conserve Estas InstruccionesÁrea DE Trabajo Seguridad EléctricaMás Calibre del cordón AWG No recomendadoSeguridad Personal USO Y Cuidados DE LA HerramientaServicio Causas del retroceso y su prevención por parte del operador D28402 D28402N D28110 D28112 Componentes Fig Ensamblado Y AjustesComo girar la caja de engranajes AccesoriosInstalación del protector Montaje Y Remoción DEL Protector D28110Operación Protectores y bridasInterruptores Interruptor DE Paleta D28402, D28402NInterruptor Deslizante D28110, D28112 Botón DE Bloqueo D28402Bloqueo DEL EJE Montaje Y Remoción DE Discos CON CuboEnsamblado DE Discos SIN Cubo Esmerilado DE Superficies CON Discos Para EsmerilarEsmerilado DE Bordes CON Discos Para Esmerilar Acabado DE Superficies CON Discos Para LijarDe aplicarla a la superficie de trabajo Mienta hacia adelante y hacia atrásMontaje y uso de cepillos de alambre y discos de alambre USO DE Almohadillas DE Respaldo Para LijarMontaje y uso de los discos de corte Tipo Montaje DEL Protector Cerrado Tipo Montaje DE LOS Discos DE CorteLa sección elevada piloto Piloto en dirección opuesta al discoMantenimiento LimpiezaLubricación ReparacionesGarantía limitada por tres años ExcepcionesAÑO DE Servicio Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasCULIACAN, SIN Especificaciones D28402, D28402N