Epson D28112 Must be used with included flanges. See, Surface Grinding with Grinding Wheels

Page 11

Depressed center Type 27 grinding wheels

G

must be used with included flanges. See

 

page 6 of this manual for more information.

 

1. Install the unthreaded backing flange

D

(G) on spindle (D) with the raised section

 

(pilot) against the wheel. Be sure the

 

backing flange recess is seated onto the flats of the spindle by pushing and twisting the flange before placing wheel.

SURFACE GRINDING WITH GRINDING WHEELS

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to the work surface, allowing the tool to operate at high speed. Grinding rate is greatest when the tool operates at high speed.

3.Maintain a 20˚ to 30˚ angle between the

tool and work surface.

English

2.Place wheel against the backing flange, centering the wheel on the raised sec- tion (pilot) of the backing flange.

3.While depressing the spindle lock but- ton, thread the clamp nut (H) on spin- dle. If the wheel you are installing is more than 1/8" (3.31mm) thick, place the threaded clamp nut on the spindle so that the raised section (pilot) fits into the center of the wheel. If the wheel you are installing is 1/8" (3.31mm) thick or less, place the threaded clamp nut on the spindle so that the raised section (pilot) is not against the wheel.

H

1/4" WHEELS

(6.35mm)

Clamp Nut

4. Continuously move the tool in a forward

 

and back motion to avoid creating

20˚-30˚

gouges in the work surface.

 

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

EDGE GRINDING WITH GRINDING WHEELS

CAUTION: Wheels used for cutting and edge grinding may break if they bend or twist while the tool is being used to do cut-off work or deep grinding. To reduce the risk of serious injury, limit the use of these wheels with a standard Type 27 guard

to shallow cutting and notching (less than 1/2" in depth). The open side of the guard must be positioned away from the operator.

4.While depressing the spindle lock button, tighten the clamp nut with a wrench.

5.To remove the wheel, depress the spin-

dle lock button and loosen the threaded clamp nut with a wrench.

NOTE: If the wheel spins after the clamp nut is tightened, check the orientation of the threaded clamp nut. If a thin wheel is installed with the pilot on the clamp nut against the wheel, it will spin because the height of the pilot prevents the clamp nut from holding the wheel.

Backing Flange

1/8" WHEELS

(3.31mm)

Clamp Nut

Backing Flange

For deeper cutting with a Type 1 cut-off wheel, use a closed, Type 1 guard. See the chart on page 7 for more information. Type 1 guards are available at extra cost from your local dealer or authorized service center.

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to the work surface, allowing the tool to operate at high speed. Grinding rate is greatest when the tool operates at high speed.

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Guide Dutilisation Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety Tool USE and Care Additional Specific Safety Instructions for GrindersPersonal Safety ServiceCauses and Operator Prevention of Kickback Always Wear EYE Protection When Using this ToolSpindle Lock Button Dust Ejection System Spindle not shown Components FigAttaching Side Handle Assembly and AdjustmentsAccessories Rotating the Gear CaseMounting and Removing Guard D28112, D28402, D28402N 2 Grinding Wheels Wire WheelsMounting Guard Type 27 depressed Center wheel Threaded clamp nutSanding Discs 2 Sanding Flap Discs Mounting and Removing Guard SwitchesOperation Guards and FlangesMounting and Removing Hubbed Wheels LOCK-ON Button D28402On button J. The tool will continue to Spindle LockEdge Grinding with Grinding Wheels Must be used with included flanges. SeeSurface Grinding with Grinding Wheels Back motion to avoid creatingVery Fine Finishing Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Mounting Sanding Backing PadsUsing Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Mounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Lubrication MaintenanceCleaning Accessories Three Year Limited WarrantyDAY Money Back Guarantee Addition to the warranty, Dewalt tools are covered by ourYear Free Service Mesures DE Sécurité Électricité Règles de sécurité GénéralitésConserver CES Directives Aire DE TravailUtilisation ET Entretien DE L’OUTIL Sécurité PersonnelleEntretien Directives de sécurité supplémentaires pour meuleusesCauses de l’effet de rebond et prévention de l’opérateur D28402 D28402N D28110 D28112 Fixation DE LA Poignée Latérale Composants figAssemblage ET Réglages Positionnement du carter d’engrenagesOuvert, tourner le dispositif I dans la AccessoiresMontage du dispositif de protection Montage ET Démontage DU Dispositif DE Protection D28110 Dispositif deAlignées, puis tirer sur le dispositif de protection FonctionnementDispositifs de protection et brides La meuleuse avec un dispositif de protection desserréInterrupteur Coulissant D28110, D28112 InterrupteursInterrupteur À Palette D28402 D28402N Bouton DE Verrouillage D28402Poser la bride tournante sur collet battu Dispositif DE Verrouillage DE LA BrocheMontage ET Démontage DE Meules À Moyeu Montage DE Meules Sans MoyeuMeulage DE Bordure Avec DES Meules Meulage DE Finition Avec DES MeulesMontage DES Patins D’APPUI ET DE Ponçage Finition DE Surface Avec DES Disques À Lamelles DE PonçageUtilisation DES Patins DE Ponçage ET D’APPUI Métalliques ou de brosses métalliques à touret De la pièceMontage D’UN Dispositif DE Protection Fermé Type Montage et utilisation de meules de coupe typeUtilisation DES Meules DE Coupe EntretienNettoyage Montage DE Meules DE CoupeContrat D’ENTRETIEN Gratuit D’UN AN LubrificationRéparations Garantie limitée de trois ansSeguridad Eléctrica Instrucciones de seguridad generalesConserve Estas Instrucciones Área DE TrabajoUSO Y Cuidados DE LA Herramienta MásCalibre del cordón AWG No recomendado Seguridad PersonalServicio Causas del retroceso y su prevención por parte del operador D28402 D28402N D28110 D28112 Accesorios Componentes FigEnsamblado Y Ajustes Como girar la caja de engranajesMontaje Y Remoción DEL Protector D28110 Instalación del protectorProtectores y bridas OperaciónInterruptor DE Paleta D28402, D28402N InterruptoresMontaje Y Remoción DE Discos CON Cubo Interruptor Deslizante D28110, D28112Botón DE Bloqueo D28402 Bloqueo DEL EJEEsmerilado DE Superficies CON Discos Para Esmerilar Ensamblado DE Discos SIN CuboMienta hacia adelante y hacia atrás Esmerilado DE Bordes CON Discos Para EsmerilarAcabado DE Superficies CON Discos Para Lijar De aplicarla a la superficie de trabajoUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje y uso de los discos de corte Tipo Piloto en dirección opuesta al disco Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte La sección elevada pilotoReparaciones MantenimientoLimpieza LubricaciónGarantía DE Reembolso DE SU Dinero POR 90 Días Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoCULIACAN, SIN Especificaciones D28402, D28402N
Top Page Image Contents