Epson D28402R, D28112 Operation, Switches, Guards and Flanges, Mounting and Removing Guard

Page 9

CAUTION: Do not tighten the adjusting screw with the clamp lever in open position. Undetectable damage to the guard or the mounting hub may result.

CAUTION: If guard cannot be tightened by adjusting clamp, do not use tool and take the tool and guard to a service center to repair or replace the guard.

MOUNTING AND REMOVING GUARD

O

(D28110)

N

1.Loosen screw. Align the lugs (N) on the guard with slots (O) on the gear case.

2. Push the guard down until the guard lug engages and rotates freely in the groove on the gear case hub.

3.Rotate guard (I) into desired working position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection.

4.Tighten the screw to secure the guard on the gear case cover. You should be unable to rotate the guard by hand. Do not operate grinder with a loose guard.

5.To remove the guard, loosen screw, rotate the guard so that the arrows are aligned and pull up on the guard.

OPERATION

it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 6–7. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

Switches

CAUTION: Hold the side handle and body of the tool firmly to maintain control of the tool at start up and during use and until the wheel or accessory stops rotating. Make sure the wheel has come to a complete stop before laying the tool down.

NOTE: To reduce unexpected tool movement, do not switch the tool on or off while under load conditions. Allow the grinder to run up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down.

PADDLE SWITCH (D28402, D28402N)

CAUTION: Before connecting the tool to a power source depress and release the paddle switch (A) once [D28402: without depress- ing the lock-on button (J)] to ensure that the switch is off. Depress and release the paddle switch as described above after any inter- ruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure. If the paddle switch is locked on, the tool will start unexpectedly when it is reconnected.

English

Guards and Flanges

It is important to choose the correct guards and flanges to use with the grinder accessories. See page 6 and this page for the correct accessories.

NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose.

To turn the tool on, push the lock-off lever (B) toward the back of the tool, then depress the paddle switch (A). The tool will run while the switch is depressed. Turn the tool off by releasing the paddle switch.

A

B

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other acces- sories running over rated accessory speed may burst and cause injury. Every unthreaded accessory must have a 7/8" arbor hole. If

WARNING: Do not disable the lock-off lever. If the lock-off lever is disabled, the tool may start unexpectedly when it is laid down.

8

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Guide Dutilisation Manual DE Instrucciones General Safety Rules For All Tools Electrical SafetyWork Area Personal Safety Additional Specific Safety Instructions for GrindersService Tool USE and CareCauses and Operator Prevention of Kickback Always Wear EYE Protection When Using this ToolSpindle Lock Button Dust Ejection System Spindle not shown Components FigAccessories Assembly and AdjustmentsRotating the Gear Case Attaching Side HandleMounting Guard 2 Grinding Wheels Wire WheelsType 27 depressed Center wheel Threaded clamp nut Mounting and Removing Guard D28112, D28402, D28402NSanding Discs 2 Sanding Flap Discs Operation SwitchesGuards and Flanges Mounting and Removing GuardOn button J. The tool will continue to LOCK-ON Button D28402Spindle Lock Mounting and Removing Hubbed WheelsSurface Grinding with Grinding Wheels Must be used with included flanges. SeeBack motion to avoid creating Edge Grinding with Grinding WheelsSurface Finishing with Sanding Flap Discs Using Sanding Backing PadsMounting Sanding Backing Pads Very Fine FinishingMounting and Using Wire Brushes and Wire Wheels Mounting Wire CUP Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 Wheels Mounting Closed Type 1 GuardMounting Cutting Wheels Cleaning MaintenanceAccessories Three Year Limited Warranty LubricationAddition to the warranty, Dewalt tools are covered by our Year Free ServiceDAY Money Back Guarantee Conserver CES Directives Règles de sécurité GénéralitésAire DE Travail Mesures DE Sécurité ÉlectricitéUtilisation ET Entretien DE L’OUTIL Sécurité PersonnelleEntretien Directives de sécurité supplémentaires pour meuleusesCauses de l’effet de rebond et prévention de l’opérateur D28402 D28402N D28110 D28112 Assemblage ET Réglages Composants figPositionnement du carter d’engrenages Fixation DE LA Poignée LatéraleAccessoires Montage du dispositif de protectionOuvert, tourner le dispositif I dans la Montage ET Démontage DU Dispositif DE Protection D28110 Dispositif deDispositifs de protection et brides FonctionnementLa meuleuse avec un dispositif de protection desserré Alignées, puis tirer sur le dispositif de protectionInterrupteur À Palette D28402 D28402N InterrupteursBouton DE Verrouillage D28402 Interrupteur Coulissant D28110, D28112Montage ET Démontage DE Meules À Moyeu Dispositif DE Verrouillage DE LA BrocheMontage DE Meules Sans Moyeu Poser la bride tournante sur collet battuMeulage DE Bordure Avec DES Meules Meulage DE Finition Avec DES MeulesFinition DE Surface Avec DES Disques À Lamelles DE Ponçage Utilisation DES Patins DE Ponçage ET D’APPUIMontage DES Patins D’APPUI ET DE Ponçage Métalliques ou de brosses métalliques à touret De la pièceMontage D’UN Dispositif DE Protection Fermé Type Montage et utilisation de meules de coupe typeNettoyage EntretienMontage DE Meules DE Coupe Utilisation DES Meules DE CoupeRéparations LubrificationGarantie limitée de trois ans Contrat D’ENTRETIEN Gratuit D’UN ANConserve Estas Instrucciones Instrucciones de seguridad generalesÁrea DE Trabajo Seguridad EléctricaCalibre del cordón AWG No recomendado MásSeguridad Personal USO Y Cuidados DE LA HerramientaServicio Causas del retroceso y su prevención por parte del operador D28402 D28402N D28110 D28112 Ensamblado Y Ajustes Componentes FigComo girar la caja de engranajes AccesoriosMontaje Y Remoción DEL Protector D28110 Instalación del protectorProtectores y bridas OperaciónInterruptor DE Paleta D28402, D28402N InterruptoresBotón DE Bloqueo D28402 Interruptor Deslizante D28110, D28112Bloqueo DEL EJE Montaje Y Remoción DE Discos CON CuboEsmerilado DE Superficies CON Discos Para Esmerilar Ensamblado DE Discos SIN CuboAcabado DE Superficies CON Discos Para Lijar Esmerilado DE Bordes CON Discos Para EsmerilarDe aplicarla a la superficie de trabajo Mienta hacia adelante y hacia atrásUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje y uso de los discos de corte Tipo Montaje DE LOS Discos DE Corte Montaje DEL Protector Cerrado TipoLa sección elevada piloto Piloto en dirección opuesta al discoLimpieza MantenimientoLubricación ReparacionesExcepciones Garantía limitada por tres añosAÑO DE Servicio Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasCULIACAN, SIN Especificaciones D28402, D28402N
Top Page Image Contents