Epson D28402R, D28112 instruction manual Mounting and Using Wire Brushes and Wire Wheels

Page 13
5˚-10˚
5˚-15˚

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed. Sanding rate is greatest when the tool operates at high speed.

3.Maintain a 5˚ to 15˚ angle between

the tool and work surface. The san- ding disc should contact approxi-

mately one inch of work surface. 4. Move the tool constantly in a straight

line to prevent burning and swirling

of work surface. Allowing the tool to rest on the work surface without moving, or moving the tool in a circular motion causes burning and swirling marks on the work surface.

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

Mounting and Using Wire Brushes and Wire Wheels

Wire cup brushes or wire wheels screw directly on the grinder spindle without the use of flanges. Use only wire brushes or wheels provided with a 5/8"-11 threaded hub. A Type 27 guard is required when using wire brushes and wheels.

CAUTION: Wear work gloves when handling wire brushes and wheels. They can become sharp.

CAUTION: Wheel or brush must not touch guard when mounted or while in use. Undetectable damage could occur to the accessory, causing wires to fragment from accessory wheel or cup.

MOUNTING WIRE CUP BRUSHES AND WIRE WHEELS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

1. Thread the wheel on the spindle by hand.

2.Depress spindle lock button and use a wrench on the hub of the wire wheel or brush to tighten the wheel.

3.To remove the wheel, reverse the above procedure.

CAUTION: Failure to properly seat the wheel hub before turning the tool on may result in damage to tool or wheel.

USING WIRE CUP BRUSHES AND WIRE WHEELS

Wire wheels and brushes can be used for removing rust, scale and paint, and for smoothing irregular surfaces.

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed. Material removal rate is greatest when the tool operates at high speed.

3. Maintain a 5˚ to 10˚ angle between the tool and work surface for wire cup

brushes. 4. Maintain contact between the edge of

the wheel and the work surface with wire wheels.

5. Continuously move the tool in a forward and back motion to avoid creating gouges in the work surface. Allowing the tool to rest on

the work surface without moving, or moving the tool in a circular motion causes burning and swirling marks on the work surface.

6.Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before setting it down.

CAUTION: Use extra care when working over an edge, as a sudden sharp movement of grinder may be experienced.

English

12

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Guide Dutilisation Manual DE Instrucciones Electrical Safety General Safety Rules For All ToolsWork Area Personal Safety Additional Specific Safety Instructions for GrindersService Tool USE and CareCauses and Operator Prevention of Kickback Always Wear EYE Protection When Using this ToolSpindle Lock Button Dust Ejection System Spindle not shown Components FigAccessories Assembly and AdjustmentsRotating the Gear Case Attaching Side HandleMounting Guard 2 Grinding Wheels Wire WheelsType 27 depressed Center wheel Threaded clamp nut Mounting and Removing Guard D28112, D28402, D28402NSanding Discs 2 Sanding Flap Discs Operation SwitchesGuards and Flanges Mounting and Removing GuardOn button J. The tool will continue to LOCK-ON Button D28402Spindle Lock Mounting and Removing Hubbed WheelsSurface Grinding with Grinding Wheels Must be used with included flanges. SeeBack motion to avoid creating Edge Grinding with Grinding WheelsSurface Finishing with Sanding Flap Discs Using Sanding Backing PadsMounting Sanding Backing Pads Very Fine FinishingMounting Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting Closed Type 1 Guard Mounting and Using Cutting Type 1 WheelsMounting Cutting Wheels Cleaning MaintenanceAccessories Three Year Limited Warranty LubricationYear Free Service Addition to the warranty, Dewalt tools are covered by ourDAY Money Back Guarantee Conserver CES Directives Règles de sécurité GénéralitésAire DE Travail Mesures DE Sécurité ÉlectricitéUtilisation ET Entretien DE L’OUTIL Sécurité PersonnelleEntretien Directives de sécurité supplémentaires pour meuleusesCauses de l’effet de rebond et prévention de l’opérateur D28402 D28402N D28110 D28112 Assemblage ET Réglages Composants figPositionnement du carter d’engrenages Fixation DE LA Poignée LatéraleMontage du dispositif de protection AccessoiresOuvert, tourner le dispositif I dans la Montage ET Démontage DU Dispositif DE Protection D28110 Dispositif deDispositifs de protection et brides FonctionnementLa meuleuse avec un dispositif de protection desserré Alignées, puis tirer sur le dispositif de protectionInterrupteur À Palette D28402 D28402N InterrupteursBouton DE Verrouillage D28402 Interrupteur Coulissant D28110, D28112Montage ET Démontage DE Meules À Moyeu Dispositif DE Verrouillage DE LA BrocheMontage DE Meules Sans Moyeu Poser la bride tournante sur collet battuMeulage DE Bordure Avec DES Meules Meulage DE Finition Avec DES MeulesUtilisation DES Patins DE Ponçage ET D’APPUI Finition DE Surface Avec DES Disques À Lamelles DE PonçageMontage DES Patins D’APPUI ET DE Ponçage Métalliques ou de brosses métalliques à touret De la pièceMontage D’UN Dispositif DE Protection Fermé Type Montage et utilisation de meules de coupe typeNettoyage EntretienMontage DE Meules DE Coupe Utilisation DES Meules DE CoupeRéparations LubrificationGarantie limitée de trois ans Contrat D’ENTRETIEN Gratuit D’UN ANConserve Estas Instrucciones Instrucciones de seguridad generalesÁrea DE Trabajo Seguridad EléctricaCalibre del cordón AWG No recomendado MásSeguridad Personal USO Y Cuidados DE LA HerramientaServicio Causas del retroceso y su prevención por parte del operador D28402 D28402N D28110 D28112 Ensamblado Y Ajustes Componentes FigComo girar la caja de engranajes AccesoriosMontaje Y Remoción DEL Protector D28110 Instalación del protectorProtectores y bridas OperaciónInterruptor DE Paleta D28402, D28402N InterruptoresBotón DE Bloqueo D28402 Interruptor Deslizante D28110, D28112Bloqueo DEL EJE Montaje Y Remoción DE Discos CON CuboEsmerilado DE Superficies CON Discos Para Esmerilar Ensamblado DE Discos SIN CuboAcabado DE Superficies CON Discos Para Lijar Esmerilado DE Bordes CON Discos Para EsmerilarDe aplicarla a la superficie de trabajo Mienta hacia adelante y hacia atrásUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje y uso de los discos de corte Tipo Montaje DE LOS Discos DE Corte Montaje DEL Protector Cerrado TipoLa sección elevada piloto Piloto en dirección opuesta al discoLimpieza MantenimientoLubricación ReparacionesExcepciones Garantía limitada por tres añosAÑO DE Servicio Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasCULIACAN, SIN Especificaciones D28402, D28402N
Top Page Image Contents