Epson D28112, D28402R Mounting and Using Cutting Type 1 Wheels, Mounting Closed Type 1 Guard

Page 14

English

Mounting and Using Cutting (Type 1) Wheels

Cutting wheels include diamond wheels and abrasive discs. Abrasive cutting wheels for metal and concrete use are available. Diamond blades for concrete cutting can also be used.

WARNING: A closed, 2-sided cutting wheel guard is not included with this tool but is required when using cutting wheels. Failure to use proper flange and guard can result in injury resulting from wheel breakage and wheel contact. See page 7 for more information.

MOUNTING CLOSED (TYPE 1) GUARD

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

1. Open the guard latch (M). Align

O

the lugs (N) on the guard with the

 

slots (O) on the gear case.

 

2. Push the guard down until the

 

guard lug engages and rotates

N

freely in the groove on the gear

 

case hub.

 

3. Rotate guard (I) into desired

M

working position. The guard body

 

should be positioned between the

 

spindle and the operator to provide

 

maximum operator protection.

 

4. Close the guard latch to secure the guard

 

on the gear case cover. You should be

 

unable to rotate the guard by hand when

I

the latch is in closed position. If rotation is

 

possible, tighten the adjusting screw (P) with clamp lever in the closed position. Do not operate grinder with a loose guard or clamp lever in open position.

5.To remove the guard, open the guard latch, rotate the guard so that the arrows are aligned and pull up on the guard.

NOTE: If, after a period of time, the guard becomes loose, tighten the adjusting screw (P) with the clamp lever in the P closed position.

CAUTION: Do not tighten adjusting screw with clamp lever in open position. Undetectable damage to guard or mounting hub may result.

MOUNTING CUTTING WHEELS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

CAUTION: Matching diameter threaded backing flange and clamp nut (included with tool) must be used for cutting wheels.

1.Place the unthreaded backing flange on spindle with the raised section (pilot) facing up. The raised section (pilot) on the back- ing flange will be against the wheel when the wheel is installed.

2.Place the wheel on the backing flange, centering the wheel on the raised section (pilot).

3.Install the threaded clamp nut with the raised section (pilot) facing away from the wheel.

4.Depress the spindle lock button and tighten clamp nut with a wrench.

5.To remove the wheel, grasp and turn while depressing the spindle lock button.

13

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Guide Dutilisation Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety Service Additional Specific Safety Instructions for GrindersPersonal Safety Tool USE and CareAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of KickbackComponents Fig Spindle Lock Button Dust Ejection System Spindle not shownRotating the Gear Case Assembly and AdjustmentsAccessories Attaching Side HandleType 27 depressed Center wheel Threaded clamp nut 2 Grinding Wheels Wire WheelsMounting Guard Mounting and Removing Guard D28112, D28402, D28402NSanding Discs 2 Sanding Flap Discs Guards and Flanges SwitchesOperation Mounting and Removing GuardSpindle Lock LOCK-ON Button D28402On button J. The tool will continue to Mounting and Removing Hubbed WheelsBack motion to avoid creating Must be used with included flanges. SeeSurface Grinding with Grinding Wheels Edge Grinding with Grinding WheelsMounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Very Fine FinishingUsing Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Mounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Accessories Three Year Limited Warranty MaintenanceCleaning LubricationDAY Money Back Guarantee Addition to the warranty, Dewalt tools are covered by ourYear Free Service Aire DE Travail Règles de sécurité GénéralitésConserver CES Directives Mesures DE Sécurité ÉlectricitéSécurité Personnelle Utilisation ET Entretien DE L’OUTILDirectives de sécurité supplémentaires pour meuleuses EntretienCauses de l’effet de rebond et prévention de l’opérateur D28402 D28402N D28110 D28112 Positionnement du carter d’engrenages Composants figAssemblage ET Réglages Fixation DE LA Poignée LatéraleOuvert, tourner le dispositif I dans la AccessoiresMontage du dispositif de protection Dispositif de Montage ET Démontage DU Dispositif DE Protection D28110La meuleuse avec un dispositif de protection desserré FonctionnementDispositifs de protection et brides Alignées, puis tirer sur le dispositif de protectionBouton DE Verrouillage D28402 InterrupteursInterrupteur À Palette D28402 D28402N Interrupteur Coulissant D28110, D28112Montage DE Meules Sans Moyeu Dispositif DE Verrouillage DE LA BrocheMontage ET Démontage DE Meules À Moyeu Poser la bride tournante sur collet battuMeulage DE Finition Avec DES Meules Meulage DE Bordure Avec DES MeulesMontage DES Patins D’APPUI ET DE Ponçage Finition DE Surface Avec DES Disques À Lamelles DE PonçageUtilisation DES Patins DE Ponçage ET D’APPUI De la pièce Métalliques ou de brosses métalliques à touretMontage et utilisation de meules de coupe type Montage D’UN Dispositif DE Protection Fermé TypeMontage DE Meules DE Coupe EntretienNettoyage Utilisation DES Meules DE CoupeGarantie limitée de trois ans LubrificationRéparations Contrat D’ENTRETIEN Gratuit D’UN ANÁrea DE Trabajo Instrucciones de seguridad generalesConserve Estas Instrucciones Seguridad EléctricaSeguridad Personal MásCalibre del cordón AWG No recomendado USO Y Cuidados DE LA HerramientaServicio Causas del retroceso y su prevención por parte del operador D28402 D28402N D28110 D28112 Como girar la caja de engranajes Componentes FigEnsamblado Y Ajustes AccesoriosInstalación del protector Montaje Y Remoción DEL Protector D28110Operación Protectores y bridasInterruptores Interruptor DE Paleta D28402, D28402NBloqueo DEL EJE Interruptor Deslizante D28110, D28112Botón DE Bloqueo D28402 Montaje Y Remoción DE Discos CON CuboEnsamblado DE Discos SIN Cubo Esmerilado DE Superficies CON Discos Para EsmerilarDe aplicarla a la superficie de trabajo Esmerilado DE Bordes CON Discos Para EsmerilarAcabado DE Superficies CON Discos Para Lijar Mienta hacia adelante y hacia atrásMontaje y uso de cepillos de alambre y discos de alambre USO DE Almohadillas DE Respaldo Para LijarMontaje y uso de los discos de corte Tipo La sección elevada piloto Montaje DEL Protector Cerrado TipoMontaje DE LOS Discos DE Corte Piloto en dirección opuesta al discoLubricación MantenimientoLimpieza ReparacionesAÑO DE Servicio Gratuito Garantía limitada por tres añosExcepciones Garantía DE Reembolso DE SU Dinero POR 90 DíasCULIACAN, SIN Especificaciones D28402, D28402N
Top Page Image Contents