DeWalt DW400 Edge Grinding with Grinding Wheels, Surface Finishing with Sanding Flap Discs

Page 11

EDGE GRINDING WITH GRINDING WHEELS

WARNING: Edge grinding and cutting can be performed only with Type 27 wheels that are designed and specified for this purpose.

WARNING: Wheels used for cutting and edge grinding may break or kick back if they bend or twist while the tool is being used to do cut-off work or deep grinding. To reduce the risk of serious injury, limit the use of these wheels with a standard Type 27 guard to shallow cutting and notching (less than 1/2" in depth). The open side of the guard must be positioned away from the operator.

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to the work

surface, allowing the tool to operate at high speed. Grinding rate is greatest when the tool operates at high speed.

3. Position yourself so that the open-under- side of the wheel is facing away from you.

4. Once a cut is begun and a notch is

SURFACE FINISHING WITH SANDING FLAP DISCS

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed. Sanding rate is greatest when the tool operates at high speed.

3.Maintain a 5˚ to 10˚ angle between

the tool and work surface.

4. Continuously move the tool in a

5˚-10˚

forward and back motion to avoid

 

creating gouges in the work surface.

 

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

MOUNTING SANDING BACKING PADS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, actuate and release switch to ensure that the tool is off.

English

established in the workpiece, do not change the angle of the cut. Changing the angle will cause the wheel to bend and may cause wheel breakage.

5.Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before laying it down.

WARNING: Do not use edge grinding/cutting wheels for surface grinding applications because these wheels are not designed for side pressures encountered with surface grinding. Wheel breakage and injury may result.

CAUTION: The proper guard must be re- installed for the grinding wheel, sanding flap disc, wire brush or wire wheel applications after sanding applications are complete.

1.Push the hub of the disc nut (M) through the center of the sanding disc (L), as far as it will go, and also through the backing disc (K).

2.Assemble the disc nut hub (J), backing pad, sanding disc, and disc nut as shown.

3.Be sure the disc nut extends through the discs into the disc nut hub.

J

K

L M

9

Image 11
Contents DW400 Page Work Area General Safety InstructionsElectrical Safety Personal SafetyTool USE and Care Additional Specific Safety Instructions for GrindersService Per minute Operation Assembly and AdjustmentsAccessories ComponentsSanding Discs 2 Grinding Wheels2 Sanding Flap Discs Wire Wheels Mounting and Removing Guard Spindle LockMounting NON-HUBBED Wheels Mounting and Removing Hubbed WheelsMounting Sanding Backing Pads Edge Grinding with Grinding WheelsSurface Finishing with Sanding Flap Discs Using Sanding Backing Pads Precautions To Take When Sanding PaintMounting Wire Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsEnvironmental Safety Cleaning and DisposalMaintenance Règles DE Sécurité Relatives À Lélectricité Directives de sécurité dordre généralConserver CES Directives Aire DE TravailUtilisation DES Outils ET Précautions Sécurité PersonnelleRéparation Composantes Fixation DE LA Poignée Latérale AccessoiresAssemblage ET Réglages FonctionnementDisques de ponçage Meules de 4 1/2 poProtecteur de type Brosse forme coupelle De 3 po Verrouillage de la broche Installation ET Dépose DU ProtecteurInstallation DE Meules Sans Moyeu Installation ET Dépose DES Roues À MoyeuFinition DE Surface AU Moyen DE Disques DE Ponçage Tronçonnage AU Moyen DE MeulesUtilisation DES Plateaux PORTE-DISQUE Installation DES Plateaux PORTE-DISQUESécurité Environnementale Nettoyage ET Mode DE DispositionPrécautions à prendre durant le ponçage de la peinture Nettoyage EntretienRéparations Achat daccessoiresLubrification Balais de moteurSeguridad Eléctrica Instrucciones de seguridad generalesConserve Estas Instrucciones Área DE TrabajoUSO Y Cuidados DE LA Herramienta Seguridad PersonalServicio Componentes Accesorios Limpieza Y AjustesFuncionamiento Fijación DE LA Agarradera LateralDiscos de lijado Discos de esmeril de 4 1/2Guarda de tipo Discos lijadores de aletas de 4 1/2 Discos de alambreMontaje Y Desmontaje DE LA Guarda Seguro del ejeMontaje Y Desmontaje DE Discos SIN Cubo Montaje Y Desmontaje DE Discos CON CuboAcabado DE Superficies CON Discos Lijadores DE Aletas Esmerilado Tangencial CON Discos DE EsmerilDe que toque la superficie de trabajo Montaje DE Almohadillas DE Apoyo Para LijadoLimpieza Y Eliminación Precauciones para el lijado de pinturaSeguridad Ambiental Montaje DE Cepillos DE Alambre Y Discos DE Alambre MantenimientoLimpieza LubricaciónPóliza de Garantía Cepillos del motorReparaciones Compra de accesoriosAÑO DE Servicio Gratuito Garantía limitada por tres añosInformación Técnica DW400