Cisco Systems 7600 manual Supported Hardware

Page 12

Chapter 1 Cisco 7600 Product Overview

Cisco 7600 Series Routers

Supported Hardware

Cisco 7600 series routers support the following hardware:

•A supervisor engine (such as the Sup720, Sup32, or Sup2) or Route Switch Processor (RSP720) with modular Gigabit Ethernet uplink ports. Each supervisor engine or RSP has two integrated daughter cards: a policy feature card (PFC) and a multilayer switch feature card (MSFC). See the “Overview” section on page 2-2for details.

Note You can install a redundant supervisor engine or RSP in the router to provide a backup in case the active module fails. Both supervisor engines or RSPs must be identical. If the system does not include a redundant supervisor engine or RSP, you can install another type of module (for example, FlexWAN, OSM, or SIP and SPA) in the slot that is reserved for the redundant processor card.

•Optical Services Modules (OSMs), FlexWAN and Enhanced FlexWAN modules, recommended Catalyst 6000 family modules, and SPA interface processors (SIPs) in any combination.

–Two additional modules for the Cisco 7603 router

–Three additional modules for the Cisco 7604 router

–Five additional modules for the Cisco 7606 router

–Eight additional modules for the Cisco 7609 router

–Twelve additional modules for the Cisco 7613 router

Note Specific combinations of supervisor engines or RSPs and modules may not be supported in

your chassis. See the Supported Hardware for Cisco 7600 Series Routers guide for information about which combinations are not supported.

•Hot-swappable fan assembly

•Redundant AC-input or DC-input power supplies

•Redundant AC-input or DC-input power entry modules (PEMs) (Cisco 7603 and Cisco 7606 routers only)

•An optional Switch Fabric Module (WS-X6500-SFM2) that is available with the Supervisor Engine 2. For redundancy, you can install a redundant SFM2 module. The module that is installed first functions as the primary module.

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

1-2	OL-10100-04

Image 12

Contents Americas Headquarters Text Part Number OL-10100-04Copyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Contents Document HistoryDocument Organization Document ConventionsChapter Title Description Convention DescriptionRelated Documentation OL-10100-04 Cisco 7600 Product Overview Cisco 7600 Series RoutersSupported Hardware Features Feature DescriptionFeature Description Port Addresses Physical Interface AddressesMAC Addresses FAN StatusRoute Switch Processors Supervisor Engines Overview Product Number Description Product Number RSP720-3CXL-GEWS-SUP720-3BXL WS-SUP32-GE-3BRoute Switch Processor WS-X6K-S2-MSFC2WS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2RSP720 Features Unsupported Hardware and FeaturesSupported Chassis, Line Cards, and Modules RSP720-10GE Features RSP720 with 10GE Uplink PortsUnsupported Features Unsupported Chassis and ModulesRSP720-10GE Usage Guidelines and Limitations QoS on the RSP720-10GEQoS Configuration Guidelines Supervisor Engine 720 and Supervisor Engine Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32 Component DescriptionColor Description Supervisor Engine Supervisor Engine 2 Front PanelSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Safety Precautions for Module Installation and Removal Preventing Electrostatic Discharge DamageTools Required for Module Installation Determining Module LocationModule Slot Assignments Installing a Supervisor Engine or Route Switch Processor ModuleEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Hot Swapping OIR Modules Removing and Replacing MemoryConnecting to the Console Port Connecting a TerminalConnecting to the Uplink Ports Connecting a ModemSupervisor Engine Module Uplink Ports Using Flash Memory Cards Locating the Flash PC Card Write-Protection SwitchInstalling a Flash Memory Card Power Management and Environmental Monitoring Determining Software Feature SupportRemoving a Flash Memory Card Module Specifications SpecificationRegulatory Standards Compliance OL-10100-04 Cable and Connector Specifications Limiting Connection DistancesUplink Port Transceiver Modules Transceiver Module Part Numbers1GE Uplink Ports and Cabling Specifications Product ID DescriptionMMF SMF10GE Uplink Ports and Cabling Specifications SMF ITU-TConsole Port Cabling Specifications and Pinouts Gbic Module Cabling SpecificationsConsole Port Cabling Specifications MHz km MicronConsole Port Signals and Pinouts Rate bps Distance feet Distance metersSignal RJ-45 Pin DB-9 Pin RJ-45-to-RJ-45 RJ-45-to-DB-9 ConsoleRollover Cable DeviceRollover Cable Modem Adapter Signal RJ-45 Pin DB-25 Pin RJ-45-to-DB-25 Terminal ConsoleRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTRRJ-45 Connector Console Port Mode 2 Signaling and Pinouts Sup2 OnlyConsole Port Console Device Side 2 Pin Signal RD+ TD+ Not usedFiber-Optic Connectors SC ConnectorsSide 1 Pin Signal Side 2 Pin Signal MT-RJ Connectors Figure B-5 SC Optical ConnectorLC Connectors Figure B-7 LC Fiber-Optic ConnectorCleaning the Fiber-Optic Connectors LX/LH Gbic and MMF Cable Considerations Patch CordPatch Cord Installation OL-10100-04 Active LED MACGBICs, connecting to Gigabit Ethernet cables Active ConsoleLink LED LX/LH GbicPWR Mgmt LED NvramStatus LED System LED

Related manuals

Manual 28 pages 32.67 Kb

Manual 12 pages 20.11 Kb

Manual 20 pages 62.17 Kb

Manual 10 pages 7.94 Kb