Cisco Systems 7600 manual Route Switch Processors Supervisor Engines

Page 17

C H A P T E R 2

Route Switch Processors and

Supervisor Engines

This chapter describes the route switch processors and supervisor engines supported on Cisco 7600 series routers and provides instructions for performing basic tasks on the modules. It contains the following sections:

Overview, page 2-2

Route Switch Processor 720, page 2-6

RSP720 with 10GE Uplink Ports, page 2-8

Supervisor Engine 720 and Supervisor Engine 32, page 2-12

Supervisor Engine 2, page 2-14

Note The route switch processor is the newest version of supervisor engine. See Table 2-1for a list of the route switch processor and supervisor engine configurations supported on Cisco 7600 series routers. Be sure to review the release notes for the software version running on your router for information about any restrictions and limitations that might apply.

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

 

OL-10100-04

2-1

 

 

 

Image 17
Contents Text Part Number OL-10100-04 Americas HeadquartersCopyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History ContentsDocument Conventions Document OrganizationChapter Title Description Convention DescriptionRelated Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product OverviewSupported Hardware Feature Description FeaturesFeature Description Physical Interface Addresses Port AddressesFAN Status MAC AddressesRoute Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product NumberWS-SUP32-GE-3B WS-SUP720-3BXLWS-X6K-S2-MSFC2 Route Switch ProcessorWS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2Supported Chassis, Line Cards, and Modules RSP720 FeaturesUnsupported Hardware and Features RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesQoS on the RSP720-10GE RSP720-10GE Usage Guidelines and LimitationsQoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor EngineColor Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Component Description Supervisor Engine 2 Front Panel Supervisor EngineSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalModule Slot Assignments Tools Required for Module InstallationDetermining Module Location Module Installing a Supervisor Engine or Route Switch ProcessorEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console PortSupervisor Engine Connecting to the Uplink PortsConnecting a Modem Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory CardsInstalling a Flash Memory Card Removing a Flash Memory Card Power Management and Environmental MonitoringDetermining Software Feature Support Regulatory Standards Compliance Module SpecificationsSpecification OL-10100-04 Limiting Connection Distances Cable and Connector SpecificationsTransceiver Module Part Numbers Uplink Port Transceiver ModulesProduct ID Description 1GE Uplink Ports and Cabling SpecificationsSMF MMFSMF ITU-T 10GE Uplink Ports and Cabling SpecificationsGbic Module Cabling Specifications Console Port Cabling Specifications and PinoutsConsole Port Cabling Specifications MHz km MicronRate bps Distance feet Distance meters Console Port Signals and PinoutsRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Signal RJ-45 Pin DB-9 PinRollover Cable DeviceRJ-45-to-DB-25 Terminal Console Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTRConsole Port Console Device RJ-45 ConnectorConsole Port Mode 2 Signaling and Pinouts Sup2 Only RD+ TD+ Not used Side 2 Pin SignalSide 1 Pin Signal Side 2 Pin Signal Fiber-Optic ConnectorsSC Connectors Figure B-5 SC Optical Connector MT-RJ ConnectorsFigure B-7 LC Fiber-Optic Connector LC ConnectorsCleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable ConsiderationsPatch Cord Installation OL-10100-04 MAC Active LEDActive Console GBICs, connecting to Gigabit Ethernet cablesLX/LH Gbic Link LEDPWR Mgmt LED NvramSystem LED Status LED
Related manuals
Manual 28 pages 32.67 Kb Manual 12 pages 20.11 Kb Manual 20 pages 62.17 Kb Manual 10 pages 7.94 Kb