Cisco Systems 7600 manual 10GE Uplink Ports and Cabling Specifications, Smf Itu-T

Page 53

Appendix B Cable and Connector Specifications

Uplink Port Transceiver Modules

10GE Uplink Ports and Cabling Specifications

Table B-4describes the X2 and XENPAK transceiver modules used for the 10GE uplink ports on the RSP720-10GE and WS-SUP32-10GE-3B. Table B-5provides cabling specifications.

Table B-4 10GE X2 and XENPAK Transceiver Modules

Product ID	Description
X2-10GB-SR	10GBASE-SR X2 or XENPAK transceiver module for MMF,
XENPAK-10GB-SR	850-nm wavelength, SC duplex connector
XENPAK-10GB-SR

X2-10GB-LR	10GBASE-LR X2 or XENPAK transceiver module for SMF,
XENPAK-10GB-LR	1310-nm wavelength, SC duplex connector
XENPAK-10GB-LR

X2-10GB-ER	10GBASE-ER X2 or XENPAK transceiver module for SMF,
XENPAK-10GB-ER	1550-nm wavelength, SC duplex connector
XENPAK-10GB-ER

X2-10GB-LX4	10GBASE-LX4 X2 or XENPAK transceiver module for MMF,
XENPAK-10GB-LX4	1310-nm wavelength, SC duplex connector
XENPAK-10GB-LX4

X2-10GB-CX4	10GBASE-CX4 X2 or XENPAK transceiver module for CX4
XENPAK-10GB-CX4	copper cable, Infiniband 4X connector
XENPAK-10GB-CX4

Table B-5lists the cabling specifications for 10GE uplink ports, which are located on X2 or XENPAK transceiver modules that plug into the RSP720-10GE and WS-SUP32-10GE-3B front panel.

Note The 10GE uplink ports on the RSP720-10GE support X2 transceiver modules only.

Table B-5	10GE Cabling Specifications

X2 Device		Wavelength	Fiber Type	Core Size	Modal Bandwidth	Cable Distance 1
(Product ID)		(nm)	(MHz km)	(micron)	(MHz km)	Cable Distance 1
X2-10GB-SR		850	MMF	62.5	160	85.3 ft (26 m)
XENPAK-10GB-SR				62.5	200	108.3 ft (33 m)
XENPAK-10GB-SR				50	400	216.5 ft (66 m)
				50	400	216.5 ft (66 m)
				50	500	269.0 ft (82 m)
				50	2000	984.3 ft (300 m)

X2-10GB-LR		1310	SMF	ITU-T	—	6.2 mi (10 km)
XENPAK-10GB-LR				G.652
XENPAK-10GB-LR

X2-10GB-ER 2		1550	SMF	ITU-T	—	24.9 mi (40 km) 3
XENPAK-10GB-ER				G.652
XENPAK-10GB-ER

X2-10GB-LX4		1310	MMF	62.5	500	984.3 ft (300 m)
XENPAK-10GB-LX4				50	400	787.4 ft (240 m)
XENPAK-10GB-LX4				50	500	984.3 ft (300 m)
				50	500	984.3 ft (300 m)

X2-10GB-CX4		—	CX4 (copper)	—	—	49.2 ft (15 m)
XENPAK-10GB-CX4

1. Minimum cabling distance for -LR, -SR, -LX4, and -ER modules is 2 m, according to the IEEE 802.3ae standard.

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

	OL-10100-04	B-5

Image 53

Contents Text Part Number OL-10100-04 Americas HeadquartersCopyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History ContentsDocument Conventions Document OrganizationChapter Title Description Convention DescriptionRelated Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product OverviewSupported Hardware Feature Description FeaturesFeature Description Physical Interface Addresses Port AddressesFAN Status MAC AddressesRoute Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product NumberWS-SUP32-GE-3B WS-SUP720-3BXLWS-X6K-S2-MSFC2 Route Switch ProcessorWS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2Supported Chassis, Line Cards, and Modules RSP720 FeaturesUnsupported Hardware and Features RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesQoS on the RSP720-10GE RSP720-10GE Usage Guidelines and LimitationsQoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor EngineColor Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Component Description Supervisor Engine 2 Front Panel Supervisor EngineSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalModule Slot Assignments Tools Required for Module InstallationDetermining Module Location Module Installing a Supervisor Engine or Route Switch ProcessorEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console PortSupervisor Engine Connecting to the Uplink PortsConnecting a Modem Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory CardsInstalling a Flash Memory Card Removing a Flash Memory Card Power Management and Environmental MonitoringDetermining Software Feature Support Regulatory Standards Compliance Module SpecificationsSpecification OL-10100-04 Limiting Connection Distances Cable and Connector SpecificationsTransceiver Module Part Numbers Uplink Port Transceiver ModulesProduct ID Description 1GE Uplink Ports and Cabling SpecificationsSMF MMFSMF ITU-T 10GE Uplink Ports and Cabling SpecificationsGbic Module Cabling Specifications Console Port Cabling Specifications and PinoutsConsole Port Cabling Specifications MHz km MicronRate bps Distance feet Distance meters Console Port Signals and PinoutsRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Signal RJ-45 Pin DB-9 PinRollover Cable DeviceRJ-45-to-DB-25 Terminal Console Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTRConsole Port Console Device RJ-45 ConnectorConsole Port Mode 2 Signaling and Pinouts Sup2 Only RD+ TD+ Not used Side 2 Pin SignalSide 1 Pin Signal Side 2 Pin Signal Fiber-Optic ConnectorsSC Connectors Figure B-5 SC Optical Connector MT-RJ ConnectorsFigure B-7 LC Fiber-Optic Connector LC ConnectorsCleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable ConsiderationsPatch Cord Installation OL-10100-04 MAC Active LEDActive Console GBICs, connecting to Gigabit Ethernet cablesLX/LH Gbic Link LEDPWR Mgmt LED NvramSystem LED Status LED

Related manuals

Manual 28 pages 32.67 Kb

Manual 12 pages 20.11 Kb

Manual 20 pages 62.17 Kb

Manual 10 pages 7.94 Kb