Cisco Systems 7600 manual Document Organization, Document Conventions, Chapter Title Description

Page 8

Preface

Document Organization

Table 1

Document History (continued)

 

 

 

 

Revision

 

Date

Change Summary

 

 

 

OL-10100-02

February 2007

Added information about the Route Switch Processor 720 (a new

 

 

 

supervisor engine) introduced in Cisco IOS Release 12.2SRB.

 

 

 

OL-10100-01

May 2006

Initial release of the document.

 

 

 

 

Document Organization

This document is organized as follows:

Chapter

Title

Description

 

 

 

Chapter 1

Cisco 7600 Product

Provides an overview of Cisco 7600 series routers, and

 

Overview

interface and port addresses.

 

 

 

Chapter 2

Route Switch Processors

Describes the route switch processors (RSPs) and

 

and Supervisor Engines

supervisor engines supported on Cisco 7600 series routers.

 

 

 

Chapter 3

Installing and Configuring

Provides instructions for installing and removing RSPs

 

Route Switch Processors

and supervisor engines and connecting to the console

 

and Supervisor Engines

and uplink ports.

 

 

 

Appendix A

Technical Specifications

Lists the technical specifications for the RSP and

 

 

supervisor engines.

 

 

 

Appendix B

Cable and Connector

Lists the cable and connector specifications for the

 

Specifications

RSPs and supervisor engines.

 

 

 

Document Conventions

This document uses the following conventions:

Convention

Description

 

 

boldface font

Commands, command options, and keywords are in boldface.

 

 

italic font

Command arguments for which you supply values are in italics.

 

 

Caution Means reader be careful. You are capable of doing something that might result in equipment damage or loss of data.

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this document.

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

 

viii

OL-10100-04

 

 

 

Image 8
Contents Americas Headquarters Text Part Number OL-10100-04Copyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Contents Document HistoryDocument Organization Document ConventionsChapter Title Description Convention DescriptionRelated Documentation OL-10100-04 Cisco 7600 Product Overview Cisco 7600 Series RoutersSupported Hardware Features Feature DescriptionFeature Description Port Addresses Physical Interface AddressesMAC Addresses FAN StatusRoute Switch Processors Supervisor Engines Overview Product Number Description Product Number RSP720-3CXL-GEWS-SUP720-3BXL WS-SUP32-GE-3BRoute Switch Processor WS-X6K-S2-MSFC2WS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2Supported Chassis, Line Cards, and Modules RSP720 FeaturesUnsupported Hardware and Features RSP720-10GE Features RSP720 with 10GE Uplink PortsUnsupported Features Unsupported Chassis and ModulesRSP720-10GE Usage Guidelines and Limitations QoS on the RSP720-10GEQoS Configuration Guidelines Supervisor Engine 720 and Supervisor Engine Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32Color Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Component Description Supervisor Engine Supervisor Engine 2 Front PanelSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Safety Precautions for Module Installation and Removal Preventing Electrostatic Discharge DamageModule Slot Assignments Tools Required for Module InstallationDetermining Module Location Installing a Supervisor Engine or Route Switch Processor ModuleEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Hot Swapping OIR Modules Removing and Replacing MemoryConnecting to the Console Port Connecting a TerminalSupervisor Engine Connecting to the Uplink PortsConnecting a Modem Module Uplink Ports Using Flash Memory Cards Locating the Flash PC Card Write-Protection SwitchInstalling a Flash Memory Card Removing a Flash Memory Card Power Management and Environmental MonitoringDetermining Software Feature Support Regulatory Standards Compliance Module SpecificationsSpecification OL-10100-04 Cable and Connector Specifications Limiting Connection DistancesUplink Port Transceiver Modules Transceiver Module Part Numbers1GE Uplink Ports and Cabling Specifications Product ID DescriptionMMF SMF10GE Uplink Ports and Cabling Specifications SMF ITU-TConsole Port Cabling Specifications and Pinouts Gbic Module Cabling SpecificationsConsole Port Cabling Specifications MHz km MicronConsole Port Signals and Pinouts Rate bps Distance feet Distance metersSignal RJ-45 Pin DB-9 Pin RJ-45-to-RJ-45 RJ-45-to-DB-9 ConsoleRollover Cable DeviceRollover Cable Modem Adapter Signal RJ-45 Pin DB-25 Pin RJ-45-to-DB-25 Terminal ConsoleRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTRConsole Port Console Device RJ-45 ConnectorConsole Port Mode 2 Signaling and Pinouts Sup2 Only Side 2 Pin Signal RD+ TD+ Not usedSide 1 Pin Signal Side 2 Pin Signal Fiber-Optic ConnectorsSC Connectors MT-RJ Connectors Figure B-5 SC Optical ConnectorLC Connectors Figure B-7 LC Fiber-Optic ConnectorCleaning the Fiber-Optic Connectors LX/LH Gbic and MMF Cable Considerations Patch CordPatch Cord Installation OL-10100-04 Active LED MACGBICs, connecting to Gigabit Ethernet cables Active ConsoleLink LED LX/LH GbicPWR Mgmt LED NvramStatus LED System LED
Related manuals
Manual 28 pages 32.67 Kb Manual 12 pages 20.11 Kb Manual 20 pages 62.17 Kb Manual 10 pages 7.94 Kb