Cisco Systems 7600 manual Product Number Description

Page 19

Chapter 2 Route Switch Processors and Supervisor Engines

Overview

Table 2-1lists the RSP and supervisor engine configurations supported on Cisco 7600 series routers. Specific combinations of processors and modules may not be supported in your chassis. See the release notes for your software version for information about supported combinations.

Table 2-1 Route Switch Processor and Supervisor Engine Configurations

Product Number

Description

Route Switch Processor 720

 

 

 

RSP720-3C-10GE

• Two 10 Gigabit Ethernet (10GE) uplink ports support 10-Gbps X2

 

modules

 

• Three Gigabit Ethernet (1GE) uplink ports: two ports support

 

1-Gbps small form-factor pluggable (SFP) module; one port

 

supports 10/100/1000-Mbps RJ-45 connector

 

Note Use Category 5 Shielded Twisted Pair cable at the port that

 

supports the10/100/1000-Mbps RJ-45 connector.

 

• Integrated 720-Gbps switch fabric

 

• PFC3C and MSFC4 with 512-MB bootflash, 4-MB NVRAM,

 

4-MB ROMmon, and several DRAM options:

 

– Route processor (RP): 1- to 4-GB DRAM (default 1 GB)

 

– Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)

 

• One CompactFlash Type II slot (512 KB) on front panel and two

 

internal CompactFlash (512 KB each for RP and SP; you can

 

optionally increase each internal CompactFlash to 1 GB)

 

• Requires larger power supplies and a high-speed fan tray

 

• QoS port architecture, 10GE ports (Rx/Tx): 8q8t/1p7q8t (CoS)

 

• QoS port architecture, 1GE ports (Rx/Tx): 2q8t/1p3q8t

 

 

RSP720-3CXL-10GE

• Two 10GE) uplink ports support 10-Gbps X2 modules

 

• Three 1GE)uplink ports: two ports support 1-Gbps small

 

form-factor pluggable (SFP) module; one port supports

 

10/100/1000-Mbps RJ-45 connector

 

Note Use Category 5 Shielded Twisted Pair cable at the port that

 

supports the10/100/1000-Mbps RJ-45 connector.

 

• Integrated 720-Gbps switch fabric

 

• PFC3CXL (high-capacity) and MSFC4 with 512-MB bootflash,

 

4-MB NVRAM, 4-MB ROMmon, and several DRAM options:

 

– Route processor (RP): 1- to 4-GB DRAM (default 2 GB)

 

– Switch processor (SP): 1- to 2-GB DRAM (default 1 GB)

 

• One CompactFlash Type II slot (512 KB) on front panel and two

 

internal CompactFlash (512 KB each for RP and SP; you can

 

optionally increase each internal CompactFlash to 1 GB)

 

• Requires larger power supplies and a high-speed fan tray

 

• QoS port architecture, 10GE ports (Rx/Tx): 8q8t/1p7q8t (CoS)

 

• QoS port architecture, 1GE ports (Rx/Tx): 2q8t/1p3q8t

 

 

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

 

OL-10100-04

2-3

 

 

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Text Part Number OL-10100-04 Americas HeadquartersCopyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History ContentsConvention Description Document OrganizationDocument Conventions Chapter Title DescriptionRelated Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product OverviewSupported Hardware Feature Description FeaturesFeature Description Physical Interface Addresses Port AddressesFAN Status MAC AddressesRoute Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product NumberWS-SUP32-GE-3B WS-SUP720-3BXLWS-X6K-S2-PFC2 Route Switch ProcessorWS-X6K-S2-MSFC2 WS-X6K-S2U-MSFC2Unsupported Hardware and Features RSP720 FeaturesSupported Chassis, Line Cards, and Modules RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesQoS on the RSP720-10GE RSP720-10GE Usage Guidelines and LimitationsQoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor EngineComponent Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Color Description Supervisor Engine 2 Front Panel Supervisor EngineSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalDetermining Module Location Tools Required for Module InstallationModule Slot Assignments Module Installing a Supervisor Engine or Route Switch ProcessorEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console PortConnecting a Modem Connecting to the Uplink PortsSupervisor Engine Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory CardsInstalling a Flash Memory Card Determining Software Feature Support Power Management and Environmental MonitoringRemoving a Flash Memory Card Specification Module SpecificationsRegulatory Standards Compliance OL-10100-04 Limiting Connection Distances Cable and Connector SpecificationsTransceiver Module Part Numbers Uplink Port Transceiver ModulesProduct ID Description 1GE Uplink Ports and Cabling SpecificationsSMF MMFSMF ITU-T 10GE Uplink Ports and Cabling SpecificationsMHz km Micron Console Port Cabling Specifications and PinoutsGbic Module Cabling Specifications Console Port Cabling SpecificationsRate bps Distance feet Distance meters Console Port Signals and PinoutsDevice Signal RJ-45 Pin DB-9 PinRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Rollover CableRTS DTR Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-DB-25 Terminal Console RJ-45-to-RJ-45 RJ-45-to-DB-25Console Port Mode 2 Signaling and Pinouts Sup2 Only RJ-45 ConnectorConsole Port Console Device RD+ TD+ Not used Side 2 Pin SignalSC Connectors Fiber-Optic ConnectorsSide 1 Pin Signal Side 2 Pin Signal Figure B-5 SC Optical Connector MT-RJ ConnectorsFigure B-7 LC Fiber-Optic Connector LC ConnectorsCleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable ConsiderationsPatch Cord Installation OL-10100-04 MAC Active LEDActive Console GBICs, connecting to Gigabit Ethernet cablesNvram Link LEDLX/LH Gbic PWR Mgmt LEDSystem LED Status LED
Related manuals
Manual 28 pages 32.67 Kb Manual 12 pages 20.11 Kb Manual 20 pages 62.17 Kb Manual 10 pages 7.94 Kb
Top Page Image Contents