Cisco Systems 7600 manual Related Documentation

Page 9

Preface

Related Documentation

Warning Definition

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

See Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers for translations of warnings and information about the compliance and safety standards with which Cisco 7600 series routers conform.

Related Documentation

The following documents provide additional information about Cisco 7600 series routers:

•Cisco 7600 Series Routers Documentation Roadmap

•Supported Hardware for Cisco 7600 Series Routers

•Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers

•Cisco 7600 Series Router Installation Guide

•Cisco 7609 Router Installation Guide (OSR-7609)

•Cisco 7600 Series Router Module Installation Guide

•Cisco 7600 Series Router Cisco IOS Command Reference

•Cisco 7600 Series Router Cisco IOS System Message Guide

•Cisco 7600 Series Router Cisco IOS Software Configuration Guide

Documentation for the Cisco 7600 series router is available online at the folowing URL: http://www.cisco.com/en/US/products/hw/routers/ps368/tsd_products_support_series_home.html For information about MIBs, refer to this URL: http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

	OL-10100-04	ix

Image 9

Contents Text Part Number OL-10100-04 Americas HeadquartersCopyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History ContentsDocument Conventions Document OrganizationChapter Title Description Convention DescriptionRelated Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product OverviewSupported Hardware Feature Description FeaturesFeature Description Physical Interface Addresses Port AddressesFAN Status MAC AddressesRoute Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product NumberWS-SUP32-GE-3B WS-SUP720-3BXLWS-X6K-S2-MSFC2 Route Switch ProcessorWS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2RSP720 Features Unsupported Hardware and FeaturesSupported Chassis, Line Cards, and Modules RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesQoS on the RSP720-10GE RSP720-10GE Usage Guidelines and LimitationsQoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor EngineFront-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32 Component DescriptionColor Description Supervisor Engine 2 Front Panel Supervisor EngineSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalTools Required for Module Installation Determining Module LocationModule Slot Assignments Module Installing a Supervisor Engine or Route Switch ProcessorEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console PortConnecting to the Uplink Ports Connecting a ModemSupervisor Engine Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory CardsInstalling a Flash Memory Card Power Management and Environmental Monitoring Determining Software Feature SupportRemoving a Flash Memory Card Module Specifications SpecificationRegulatory Standards Compliance OL-10100-04 Limiting Connection Distances Cable and Connector SpecificationsTransceiver Module Part Numbers Uplink Port Transceiver ModulesProduct ID Description 1GE Uplink Ports and Cabling SpecificationsSMF MMFSMF ITU-T 10GE Uplink Ports and Cabling SpecificationsGbic Module Cabling Specifications Console Port Cabling Specifications and PinoutsConsole Port Cabling Specifications MHz km MicronRate bps Distance feet Distance meters Console Port Signals and PinoutsRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Signal RJ-45 Pin DB-9 PinRollover Cable DeviceRJ-45-to-DB-25 Terminal Console Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTRRJ-45 Connector Console Port Mode 2 Signaling and Pinouts Sup2 OnlyConsole Port Console Device RD+ TD+ Not used Side 2 Pin SignalFiber-Optic Connectors SC ConnectorsSide 1 Pin Signal Side 2 Pin Signal Figure B-5 SC Optical Connector MT-RJ ConnectorsFigure B-7 LC Fiber-Optic Connector LC ConnectorsCleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable ConsiderationsPatch Cord Installation OL-10100-04 MAC Active LEDActive Console GBICs, connecting to Gigabit Ethernet cablesLX/LH Gbic Link LEDPWR Mgmt LED NvramSystem LED Status LED

Related manuals

Manual 28 pages 32.67 Kb

Manual 12 pages 20.11 Kb

Manual 20 pages 62.17 Kb

Manual 10 pages 7.94 Kb