Cisco Systems 7600 manual Side 2 Pin Signal, RD+ TD+ Not used

Page 59

Appendix B Cable and Connector Specifications

RJ-45 Connector

Figure B-2 RJ-45 Interface Cable Connector

				48129
Table B-12		10/100BASE-T Crossover Cable Pinout (MDI-X)
Side 1 Pin (Signal)			Side 2 Pin (Signal)
1	(RD+)		3	(TD+)
2	(RD–)		6	(TD–)
3	(TD+)		1	(RD+)
6	(TD–)		2	(RD–)
4	(Not used)		4	(Not used)
5	(Not used)		5	(Not used)
7	(Not used)		7	(Not used)
8	(Not used)		8	(Not used)

Figure B-3

Switch

1 RD+

2 RD-

3TD+

6TD-

4NC

5NC

7NC

8NC

Twisted-Pair Crossover 10/100BASE-T Cable Schematic

		Switch
	1	RD+
	2	RD-
	3	TD+
	6	TD-
	4	NC
	5	NC
	7	NC	65273
	8	NC	65273
	8	NC

		Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

	OL-10100-04			B-11
	OL-10100-04			B-11

Image 59

Contents Text Part Number OL-10100-04 Americas HeadquartersCopyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History ContentsConvention Description Document OrganizationDocument Conventions Chapter Title DescriptionRelated Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product OverviewSupported Hardware Feature Description FeaturesFeature Description Physical Interface Addresses Port AddressesFAN Status MAC AddressesRoute Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product NumberWS-SUP32-GE-3B WS-SUP720-3BXLWS-X6K-S2-PFC2 Route Switch ProcessorWS-X6K-S2-MSFC2 WS-X6K-S2U-MSFC2Supported Chassis, Line Cards, and Modules RSP720 FeaturesUnsupported Hardware and Features RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesQoS on the RSP720-10GE RSP720-10GE Usage Guidelines and LimitationsQoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor EngineColor Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Component Description Supervisor Engine 2 Front Panel Supervisor EngineSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalModule Slot Assignments Tools Required for Module InstallationDetermining Module Location Module Installing a Supervisor Engine or Route Switch ProcessorEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console PortSupervisor Engine Connecting to the Uplink PortsConnecting a Modem Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory CardsInstalling a Flash Memory Card Removing a Flash Memory Card Power Management and Environmental MonitoringDetermining Software Feature Support Regulatory Standards Compliance Module SpecificationsSpecification OL-10100-04 Limiting Connection Distances Cable and Connector SpecificationsTransceiver Module Part Numbers Uplink Port Transceiver ModulesProduct ID Description 1GE Uplink Ports and Cabling SpecificationsSMF MMFSMF ITU-T 10GE Uplink Ports and Cabling SpecificationsMHz km Micron Console Port Cabling Specifications and PinoutsGbic Module Cabling Specifications Console Port Cabling SpecificationsRate bps Distance feet Distance meters Console Port Signals and PinoutsDevice Signal RJ-45 Pin DB-9 PinRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Rollover CableRTS DTR Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-DB-25 Terminal Console RJ-45-to-RJ-45 RJ-45-to-DB-25Console Port Console Device RJ-45 ConnectorConsole Port Mode 2 Signaling and Pinouts Sup2 Only RD+ TD+ Not used Side 2 Pin SignalSide 1 Pin Signal Side 2 Pin Signal Fiber-Optic ConnectorsSC Connectors Figure B-5 SC Optical Connector MT-RJ ConnectorsFigure B-7 LC Fiber-Optic Connector LC ConnectorsCleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable ConsiderationsPatch Cord Installation OL-10100-04 MAC Active LEDActive Console GBICs, connecting to Gigabit Ethernet cablesNvram Link LEDLX/LH Gbic PWR Mgmt LEDSystem LED Status LED

Related manuals

Manual 28 pages 32.67 Kb

Manual 12 pages 20.11 Kb

Manual 20 pages 62.17 Kb

Manual 10 pages 7.94 Kb