Cisco Systems 7600 manual RJ-45 Connector, Console Port Mode 2 Signaling and Pinouts Sup2 Only

Page 58

Appendix B Cable and Connector Specifications

RJ-45 Connector

Console Port Mode 2 Signaling and Pinouts (Sup2 Only)

Table B-11lists the pinouts for the Supervisor Engine 2 console port mode switch in mode 2 (switch in the out position). In this mode, you can connect a terminal to the supervisor engine using a Catalyst 5000 family Supervisor Engine III console cable and adapter (not provided). For instructions, see “Supervisor Engine 2” in the “Connecting a Terminal” section on page 3-9.

Table B-11 Console Port Pinouts (Supervisor Engine 2, Port Mode Switch Out)

Console Port

Console Device

 

 

Pin (Signal Name)

Input/Output

 

 

 

1

(RTS)1

Output

2

(DTR)

Output

 

 

 

3

(RxD)

Input

 

 

 

4

(GND)

GND

 

 

 

5

(GND)

GND

 

 

 

6

(TxD)

Output

 

 

 

7

(DSR)

Input

 

 

 

8

(CTS)1

Input

1. Pin 1 is connected internally to Pin 8.

RJ-45 Connector

The RJ-45 connector is used to connect a Category 3, Category 5, Category 5e, or Category 6 FTP from the external network to the module interface connector. (See Figure B-2.) Table B-12lists the connector pinouts and signal names for a 10/100BASE-T crossover (MDI-X) cable. Figure B-3shows a schematic of the 10/100BASE-T crossover cable. Table B-13lists the connector pinouts and signal names for a 1000BASE-T crossover (MDI-X) cable. Figure B-4shows a schematic of the 1000BASE-T crossover cable.

Caution Category 5e and Category 6 cables can store high levels of static electricity because of the dielectric properties of the materials used in their construction. Always ground the cables (especially in new cable runs) to a suitable and safe earth ground before connecting them to the module.

Caution To comply with Telcordia GR-1089 intrabuilding, lightning-immunity requirements, you must use foil-twisted pair (FTP) cable that is properly grounded at both ends.

Inline power for IP phones uses connector pins 1, 2, 3, and 6 in a Category 5, Category 5e, or Category 6 cable to transmit power (6.3 W) from the router. This method of supplying power is sometimes called phantom power because the IP phone power travels over the same pairs of wires used to transmit the Ethernet signals. The IP phone voltage is completely transparent to the Ethernet signals and does not interfere with their operation.

 

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

B-10

OL-10100-04

Image 58
Contents Americas Headquarters Text Part Number OL-10100-04Copyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Contents Document HistoryChapter Title Description Document OrganizationDocument Conventions Convention DescriptionRelated Documentation OL-10100-04 Cisco 7600 Product Overview Cisco 7600 Series RoutersSupported Hardware Features Feature DescriptionFeature Description Port Addresses Physical Interface AddressesMAC Addresses FAN StatusRoute Switch Processors Supervisor Engines Overview Product Number Description Product Number RSP720-3CXL-GEWS-SUP720-3BXL WS-SUP32-GE-3BWS-X6K-S2U-MSFC2 Route Switch ProcessorWS-X6K-S2-MSFC2 WS-X6K-S2-PFC2Unsupported Hardware and Features RSP720 FeaturesSupported Chassis, Line Cards, and Modules RSP720-10GE Features RSP720 with 10GE Uplink PortsUnsupported Features Unsupported Chassis and ModulesRSP720-10GE Usage Guidelines and Limitations QoS on the RSP720-10GEQoS Configuration Guidelines Supervisor Engine 720 and Supervisor Engine Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32Component Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Color Description Supervisor Engine Supervisor Engine 2 Front PanelSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Safety Precautions for Module Installation and Removal Preventing Electrostatic Discharge DamageDetermining Module Location Tools Required for Module InstallationModule Slot Assignments Installing a Supervisor Engine or Route Switch Processor ModuleEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Hot Swapping OIR Modules Removing and Replacing MemoryConnecting to the Console Port Connecting a TerminalConnecting a Modem Connecting to the Uplink PortsSupervisor Engine Module Uplink Ports Using Flash Memory Cards Locating the Flash PC Card Write-Protection SwitchInstalling a Flash Memory Card Determining Software Feature Support Power Management and Environmental MonitoringRemoving a Flash Memory Card Specification Module SpecificationsRegulatory Standards Compliance OL-10100-04 Cable and Connector Specifications Limiting Connection DistancesUplink Port Transceiver Modules Transceiver Module Part Numbers1GE Uplink Ports and Cabling Specifications Product ID DescriptionMMF SMF10GE Uplink Ports and Cabling Specifications SMF ITU-TConsole Port Cabling Specifications Console Port Cabling Specifications and PinoutsGbic Module Cabling Specifications MHz km MicronConsole Port Signals and Pinouts Rate bps Distance feet Distance metersRollover Cable Signal RJ-45 Pin DB-9 PinRJ-45-to-RJ-45 RJ-45-to-DB-9 Console DeviceRJ-45-to-RJ-45 RJ-45-to-DB-25 Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-DB-25 Terminal Console RTS DTRConsole Port Mode 2 Signaling and Pinouts Sup2 Only RJ-45 ConnectorConsole Port Console Device Side 2 Pin Signal RD+ TD+ Not usedSC Connectors Fiber-Optic ConnectorsSide 1 Pin Signal Side 2 Pin Signal MT-RJ Connectors Figure B-5 SC Optical ConnectorLC Connectors Figure B-7 LC Fiber-Optic ConnectorCleaning the Fiber-Optic Connectors LX/LH Gbic and MMF Cable Considerations Patch CordPatch Cord Installation OL-10100-04 Active LED MACGBICs, connecting to Gigabit Ethernet cables Active ConsolePWR Mgmt LED Link LEDLX/LH Gbic NvramStatus LED System LED
Related manuals
Manual 28 pages 32.67 Kb Manual 12 pages 20.11 Kb Manual 20 pages 62.17 Kb Manual 10 pages 7.94 Kb