Cisco Systems 7600 manual MT-RJ Connectors, Figure B-5 SC Optical Connector

Page 61

Appendix B Cable and Connector Specifications

Fiber-Optic Connectors

Figure B-5 SC Optical Connector

H2214

Always make sure that you insert the connector completely into the socket. This action is especially important when you are making a connection between a module and a long distance (1.24 miles

[2 kilometers]) or a suspected highly attenuated network. If the LINK LED on the supervisor engine or route switch processor does not light, try removing the network cable plug and reinserting it firmly into the module socket. It is possible that enough dirt or skin oils have accumulated on the plug faceplate (around the optical-fiber openings) to generate significant attenuation, reducing the optical power levels below threshold levels so that a link cannot be made.

Caution Use extreme care when removing or installing connectors so that you do not damage the connector housing or scratch the end-face surface of the fiber. Always install protective covers on unused or disconnected components to prevent contamination. Always clean fiber connectors before installing them.

For fiber-optic connector cleaning instructions, see the “Cleaning the Fiber-Optic Connectors” section on page B-15.

MT-RJ Connectors

Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051

The MT-RJ style connector is used on fiber-optic modules to increase port density. (See Figure B-6.)

Figure B-6 MT-RJ Optical Connector

14367

When you are connecting MT-RJ cables to a module, make sure you firmly press the connector plug into the socket. The upper edge of the plug must snap into the upper front edge of the socket. You may or may not hear an audible click. Gently pull on the plug to confirm whether or not the plug is locked into the socket. To disconnect the plug from the socket, press down on the raised portion on top of the plug (releasing the latch). You should hear an audible click indicating that the latch has released. Carefully pull the plug out of the socket.

 

 

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

 

 

 

 

 

 

 

OL-10100-04

 

 

B-13

 

 

 

 

 

Image 61
Contents Text Part Number OL-10100-04 Americas HeadquartersCopyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History ContentsDocument Conventions Document OrganizationChapter Title Description Convention DescriptionRelated Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product OverviewSupported Hardware Feature Description FeaturesFeature Description Physical Interface Addresses Port AddressesFAN Status MAC AddressesRoute Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product NumberWS-SUP32-GE-3B WS-SUP720-3BXLWS-X6K-S2-MSFC2 Route Switch ProcessorWS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2Unsupported Hardware and Features RSP720 FeaturesSupported Chassis, Line Cards, and Modules RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesQoS on the RSP720-10GE RSP720-10GE Usage Guidelines and LimitationsQoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor EngineComponent Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Color Description Supervisor Engine 2 Front Panel Supervisor EngineSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalDetermining Module Location Tools Required for Module InstallationModule Slot Assignments Module Installing a Supervisor Engine or Route Switch ProcessorEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console PortConnecting a Modem Connecting to the Uplink PortsSupervisor Engine Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory CardsInstalling a Flash Memory Card Determining Software Feature Support Power Management and Environmental MonitoringRemoving a Flash Memory Card Specification Module SpecificationsRegulatory Standards Compliance OL-10100-04 Limiting Connection Distances Cable and Connector SpecificationsTransceiver Module Part Numbers Uplink Port Transceiver ModulesProduct ID Description 1GE Uplink Ports and Cabling SpecificationsSMF MMFSMF ITU-T 10GE Uplink Ports and Cabling SpecificationsGbic Module Cabling Specifications Console Port Cabling Specifications and PinoutsConsole Port Cabling Specifications MHz km MicronRate bps Distance feet Distance meters Console Port Signals and PinoutsRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Signal RJ-45 Pin DB-9 PinRollover Cable DeviceRJ-45-to-DB-25 Terminal Console Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTRConsole Port Mode 2 Signaling and Pinouts Sup2 Only RJ-45 ConnectorConsole Port Console Device RD+ TD+ Not used Side 2 Pin SignalSC Connectors Fiber-Optic ConnectorsSide 1 Pin Signal Side 2 Pin Signal Figure B-5 SC Optical Connector MT-RJ ConnectorsFigure B-7 LC Fiber-Optic Connector LC ConnectorsCleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable ConsiderationsPatch Cord Installation OL-10100-04 MAC Active LEDActive Console GBICs, connecting to Gigabit Ethernet cablesLX/LH Gbic Link LEDPWR Mgmt LED NvramSystem LED Status LED
Related manuals
Manual 28 pages 32.67 Kb Manual 12 pages 20.11 Kb Manual 20 pages 62.17 Kb Manual 10 pages 7.94 Kb