Cisco Systems 7600 manual 1GE Uplink Ports and Cabling Specifications, Product ID Description

Page 51

Appendix B Cable and Connector Specifications

Uplink Port Transceiver Modules

Table B-1 Uplink Port Transceiver Modules (continued)

Supervisor Engine or RSP	Transceiver Module Part Numbers

Supervisor Engine 32	10GE Uplink Ports (WS-SUP32-10GE-3B only):
	XENPAK-10GB-CX4
	XENPAK-10GB-SR
	XENPAK-10GB-LX4
	XENPAK-10GB-LR
	XENPAK-10GB-ER
	1GE Uplink Ports (WS-SUP32-GE-3B):
	GLC-SX-MM
	GLC-LH-SM
	GLC-ZX-SM
	GLC-T

Supervisor Engine 2	1000BASE-X GBIC modules, which are preinstalled

1GE Uplink Ports and Cabling Specifications

Table B-2describes the 1GE SFP transceiver modules that are used for Cisco 7600 uplink ports. Table B-3provides cabling specifications.

Note Use Category 5 Shielded Twisted Pair cable at the port that supports the10/100/1000-Mbps RJ-45 connector for the RSP720-10GE.

Table B-2 1GE SFP Transceiver Modules

Product ID

Description

Copper Modules

GLC-SX-MM	1000BASE-SX SFP transceiver module for multimode fiber
	(MMF), 850-nm wavelength, LC connector

GLC-LH-SM	1000BASE-LX/LH SFP transceiver module for MMF and
	single-mode fiber (SMF), 1300-nm wavelength, LC connector

GLC-ZX-SM	1000BASE-ZX SFP transceiver module for SMF,
	1550-nm wavelength, LC connector

GLC-T	1000BASE-T SFP transceiver module for Category 5, 5e, or 6
	copper wire; 10/100/1000-Mbps RJ-45 connector

GLC-BX-D	1000BASE-BX10 SFP module for single-strand SMF,
	1490-nm TX/1310-nm RX wavelength (downstream use in
	bidirectional single fiber applications), with Digital Optical
	Monitoring (DOM), LC connector

GLC-BX-U	1000BASE-BX10 SFP module for single-strand SMF,
	1310-nm TX/1490-nm RX wavelength (upstream use in
	bidirectional single fiber applications), with DOM, LC connector

Fiber Modules

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

	OL-10100-04	B-3

Image 51

Contents Text Part Number OL-10100-04 Americas HeadquartersCopyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History ContentsConvention Description Document OrganizationDocument Conventions Chapter Title DescriptionRelated Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product OverviewSupported Hardware Feature Description FeaturesFeature Description Physical Interface Addresses Port AddressesFAN Status MAC AddressesRoute Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product NumberWS-SUP32-GE-3B WS-SUP720-3BXLWS-X6K-S2-PFC2 Route Switch ProcessorWS-X6K-S2-MSFC2 WS-X6K-S2U-MSFC2RSP720 Features Unsupported Hardware and FeaturesSupported Chassis, Line Cards, and Modules RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesQoS on the RSP720-10GE RSP720-10GE Usage Guidelines and LimitationsQoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor EngineFront-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32 Component DescriptionColor Description Supervisor Engine 2 Front Panel Supervisor EngineSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalTools Required for Module Installation Determining Module LocationModule Slot Assignments Module Installing a Supervisor Engine or Route Switch ProcessorEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console PortConnecting to the Uplink Ports Connecting a ModemSupervisor Engine Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory CardsInstalling a Flash Memory Card Power Management and Environmental Monitoring Determining Software Feature SupportRemoving a Flash Memory Card Module Specifications SpecificationRegulatory Standards Compliance OL-10100-04 Limiting Connection Distances Cable and Connector SpecificationsTransceiver Module Part Numbers Uplink Port Transceiver ModulesProduct ID Description 1GE Uplink Ports and Cabling SpecificationsSMF MMFSMF ITU-T 10GE Uplink Ports and Cabling SpecificationsMHz km Micron Console Port Cabling Specifications and PinoutsGbic Module Cabling Specifications Console Port Cabling SpecificationsRate bps Distance feet Distance meters Console Port Signals and PinoutsDevice Signal RJ-45 Pin DB-9 PinRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Rollover CableRTS DTR Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-DB-25 Terminal Console RJ-45-to-RJ-45 RJ-45-to-DB-25RJ-45 Connector Console Port Mode 2 Signaling and Pinouts Sup2 OnlyConsole Port Console Device RD+ TD+ Not used Side 2 Pin SignalFiber-Optic Connectors SC ConnectorsSide 1 Pin Signal Side 2 Pin Signal Figure B-5 SC Optical Connector MT-RJ ConnectorsFigure B-7 LC Fiber-Optic Connector LC ConnectorsCleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable ConsiderationsPatch Cord Installation OL-10100-04 MAC Active LEDActive Console GBICs, connecting to Gigabit Ethernet cablesNvram Link LEDLX/LH Gbic PWR Mgmt LEDSystem LED Status LED

Related manuals

Manual 28 pages 32.67 Kb

Manual 12 pages 20.11 Kb

Manual 20 pages 62.17 Kb

Manual 10 pages 7.94 Kb