Cisco Systems 7600 manual Ejector Levers and Captive Installation Screws

Page 37

Chapter 3 Installing and Configuring Route Switch Processors and Supervisor Engines

Installing a Supervisor Engine or Route Switch Processor

Figure 3-1 Ejector Levers and Captive Installation Screws

OSM-4OC12-POS-MM
	1
STATUS	2
4 PORT OC-12 POS MM	LINK			LINK
	LINK	1	2	LINK

3

4

LINK

3

4

LINK

	ACTIVE	RX		TX
		TX
RESET		RX
RESET	CARRIERALARM		PORT	1

ACTIVE	RX		TX
	TX
CARRIERALARM	RX	PORT
CARRIERALARM		PORT	2

ACTIVE	RX		TX
	TX
CARRIERALARM	RX	PORT
CARRIERALARM		PORT	3

ACTIVE	RX		TX
	TX
CARRIERALARM	RX	PORT
CARRIERALARM		PORT	4

Captive

Ejector lever installation screws

45168

Step 4 Position the module in the slot. Make sure that you align the sides of the module with the guides on each side of the slot. (See Figure 3-2.)

Figure 3-2 Positioning the Module in the Slot

Insert module between slot guides

EMI gasket

3

1

2

36

WS-X6K-SUP2-2GE

SUPERVISOR2

	CONSOLE
	PORT
CONSOLE	MODE

-12 P
PCMCIA	EJECT
OSM-4OC12 POS-SI
4 PORT OC-12 POS SM IR

Switch Load 100%

PORT 1

PORT 2

1%

EMI gasket

Ejector lever fully extended

OL-10100-04

63677

Cisco 7600 Series Router Supervisor Engine and Route Switch Processor Guide

3-5

Image 37

Contents Text Part Number OL-10100-04 Americas HeadquartersCopyright 2007-2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Precautions for Module Installation and Removal Cleaning the Fiber-Optic Connectors B-15 OL-10100-04 Document History ContentsDocument Conventions Document OrganizationChapter Title Description Convention DescriptionRelated Documentation OL-10100-04 Cisco 7600 Series Routers Cisco 7600 Product OverviewSupported Hardware Feature Description FeaturesFeature Description Physical Interface Addresses Port AddressesFAN Status MAC AddressesRoute Switch Processors Supervisor Engines Overview Product Number Description RSP720-3CXL-GE Product NumberWS-SUP32-GE-3B WS-SUP720-3BXLWS-X6K-S2-MSFC2 Route Switch ProcessorWS-X6K-S2U-MSFC2 WS-X6K-S2-PFC2Unsupported Hardware and Features RSP720 FeaturesSupported Chassis, Line Cards, and Modules RSP720 with 10GE Uplink Ports RSP720-10GE FeaturesUnsupported Chassis and Modules Unsupported FeaturesQoS on the RSP720-10GE RSP720-10GE Usage Guidelines and LimitationsQoS Configuration Guidelines Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32 Supervisor Engine 720 and Supervisor EngineComponent Description Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32Color Description Supervisor Engine 2 Front Panel Supervisor EngineSection on page 3-10 for more information Off when you insert a card Preparing for Installation or Removal Preventing Electrostatic Discharge Damage Safety Precautions for Module Installation and RemovalDetermining Module Location Tools Required for Module InstallationModule Slot Assignments Module Installing a Supervisor Engine or Route Switch ProcessorEjector Levers and Captive Installation Screws See Figure Removing a Supervisor Engine or Route Switch Processor Removing and Replacing Memory Hot Swapping OIR ModulesConnecting a Terminal Connecting to the Console PortConnecting a Modem Connecting to the Uplink PortsSupervisor Engine Module Uplink Ports Locating the Flash PC Card Write-Protection Switch Using Flash Memory CardsInstalling a Flash Memory Card Determining Software Feature Support Power Management and Environmental MonitoringRemoving a Flash Memory Card Specification Module SpecificationsRegulatory Standards Compliance OL-10100-04 Limiting Connection Distances Cable and Connector SpecificationsTransceiver Module Part Numbers Uplink Port Transceiver ModulesProduct ID Description 1GE Uplink Ports and Cabling SpecificationsSMF MMFSMF ITU-T 10GE Uplink Ports and Cabling SpecificationsGbic Module Cabling Specifications Console Port Cabling Specifications and PinoutsConsole Port Cabling Specifications MHz km MicronRate bps Distance feet Distance meters Console Port Signals and PinoutsRJ-45-to-RJ-45 RJ-45-to-DB-9 Console Signal RJ-45 Pin DB-9 PinRollover Cable DeviceRJ-45-to-DB-25 Terminal Console Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 PinRJ-45-to-RJ-45 RJ-45-to-DB-25 RTS DTRConsole Port Mode 2 Signaling and Pinouts Sup2 Only RJ-45 ConnectorConsole Port Console Device RD+ TD+ Not used Side 2 Pin SignalSC Connectors Fiber-Optic ConnectorsSide 1 Pin Signal Side 2 Pin Signal Figure B-5 SC Optical Connector MT-RJ ConnectorsFigure B-7 LC Fiber-Optic Connector LC ConnectorsCleaning the Fiber-Optic Connectors Patch Cord LX/LH Gbic and MMF Cable ConsiderationsPatch Cord Installation OL-10100-04 MAC Active LEDActive Console GBICs, connecting to Gigabit Ethernet cablesLX/LH Gbic Link LEDPWR Mgmt LED NvramSystem LED Status LED

Related manuals

Manual 28 pages 32.67 Kb

Manual 12 pages 20.11 Kb

Manual 20 pages 62.17 Kb

Manual 10 pages 7.94 Kb