Contents
Americas Headquarters
Text Part Number OL-10100-04
Copyright 2007-2008 Cisco Systems, Inc. All rights reserved
N T E N T S
Safety Precautions for Module Installation and Removal
Cleaning the Fiber-Optic Connectors B-15
OL-10100-04
Contents
Document History
Document Organization
Document Conventions
Chapter Title Description
Convention Description
Related Documentation
OL-10100-04
Cisco 7600 Product Overview
Cisco 7600 Series Routers
Supported Hardware
Features
Feature Description
Feature Description
Port Addresses
Physical Interface Addresses
MAC Addresses
FAN Status
Route Switch Processors Supervisor Engines
Overview
Product Number Description
Product Number
RSP720-3CXL-GE
WS-SUP720-3BXL
WS-SUP32-GE-3B
Route Switch Processor
WS-X6K-S2-MSFC2
WS-X6K-S2U-MSFC2
WS-X6K-S2-PFC2
Unsupported Hardware and Features
RSP720 Features
Supported Chassis, Line Cards, and Modules
RSP720-10GE Features
RSP720 with 10GE Uplink Ports
Unsupported Features
Unsupported Chassis and Modules
RSP720-10GE Usage Guidelines and Limitations
QoS on the RSP720-10GE
QoS Configuration Guidelines
Supervisor Engine 720 and Supervisor Engine
Front-Panel Controls RSP720, RSP720-10GE, Sup720, Sup32
Component Description
Front-Panel LEDs RSP720, RSP720-10GE, Sup720, Sup32
Color Description
Supervisor Engine
Supervisor Engine 2 Front Panel
Section on page 3-10 for more information
Off when you insert a card
Preparing for Installation or Removal
Safety Precautions for Module Installation and Removal
Preventing Electrostatic Discharge Damage
Determining Module Location
Tools Required for Module Installation
Module Slot Assignments
Installing a Supervisor Engine or Route Switch Processor
Module
Ejector Levers and Captive Installation Screws
See Figure
Removing a Supervisor Engine or Route Switch Processor
Hot Swapping OIR Modules
Removing and Replacing Memory
Connecting to the Console Port
Connecting a Terminal
Connecting a Modem
Connecting to the Uplink Ports
Supervisor Engine
Module Uplink Ports
Using Flash Memory Cards
Locating the Flash PC Card Write-Protection Switch
Installing a Flash Memory Card
Determining Software Feature Support
Power Management and Environmental Monitoring
Removing a Flash Memory Card
Specification
Module Specifications
Regulatory Standards Compliance
OL-10100-04
Cable and Connector Specifications
Limiting Connection Distances
Uplink Port Transceiver Modules
Transceiver Module Part Numbers
1GE Uplink Ports and Cabling Specifications
Product ID Description
MMF
SMF
10GE Uplink Ports and Cabling Specifications
SMF ITU-T
Console Port Cabling Specifications and Pinouts
Gbic Module Cabling Specifications
Console Port Cabling Specifications
MHz km Micron
Console Port Signals and Pinouts
Rate bps Distance feet Distance meters
Signal RJ-45 Pin DB-9 Pin
RJ-45-to-RJ-45 RJ-45-to-DB-9 Console
Rollover Cable
Device
Rollover Cable Modem Adapter Signal RJ-45 Pin DB-25 Pin
RJ-45-to-DB-25 Terminal Console
RJ-45-to-RJ-45 RJ-45-to-DB-25
RTS DTR
Console Port Mode 2 Signaling and Pinouts Sup2 Only
RJ-45 Connector
Console Port Console Device
Side 2 Pin Signal
RD+ TD+ Not used
SC Connectors
Fiber-Optic Connectors
Side 1 Pin Signal Side 2 Pin Signal
MT-RJ Connectors
Figure B-5 SC Optical Connector
LC Connectors
Figure B-7 LC Fiber-Optic Connector
Cleaning the Fiber-Optic Connectors
LX/LH Gbic and MMF Cable Considerations
Patch Cord
Patch Cord Installation
OL-10100-04
Active LED
MAC
GBICs, connecting to Gigabit Ethernet cables
Active Console
Link LED
LX/LH Gbic
PWR Mgmt LED
Nvram
Status LED
System LED