ATON DH44 manual Pre-Wiring

Page 12

DH44 4 Source, 4 Zone Digital Audio Router

Pre-Construction

In a pre-construction installation, walls and ceilings are open with no drywall installed. This is desirable and allows the installer greater access than in retro-fi t applications.

Before actually running any wire or cable, take the time to look around each room or area of the house and plan your wire paths for maximum effi ciency. Look for routes through uncluttered parts of the stud wall or ceiling that allow you to group all low-voltage (video, speaker wires, Cat- 5, telephone, etc.) wires wherever possible. It is a good practice to label both ends of all cables and to protect wires by tying a plastic bag over the ends.

Note: Do not run low-voltage wires closer than 12" from high-voltage wires. If necessary, cross low-voltage wires at a 90º angle to prevent interference.

Retro-Fit Wiring/PostConstruction

Retro-fi t installations are more diffi cult to complete than pre-construction because walls and ceilings are intact. Typically wires must be fi shed into position through walls, fl oors and ceilings. Holes must be cut; speakers mounted directly in the ceiling or walls with no rough-in brackets and Touch Pads and local source wall plates must be mounted in existing drywall.

Pre-Wiring

DH44 to DHTP1 Touch Pads

The DH44 and all associated components are wired using Cat-5 terminated to the T-568A Wir- ing Standard (Figure 2-2). When pre-wiring, run lengths of Cat-5 from the pre-determined equip- ment location (the “head-end”) to each Touch Pad location. The Cat-5 routes all audio, power, IR and status information needed for full system operation.

Note: For maximum performance over long runs (more than 150 ft) run an additional 16AWG 2-conductor wire for external power.

1 2 3 4 5 6 7 8

Shown tab down

1 2 3 4 5 6 78

GREEN/WHITE

GREEN

ORANGE/WHITE

BLUE

BLUE/WHITE

ORANGE

BROWN/WHITE

BROWN

Figure 2-2 : T-568A Wiring Standard

Touch Pads to Speakers

Run 16AWG 2 conductor stranded copper speaker wire between Touch Pad locations and speaker locations.

Local Sources to Touch Pads

Local sources are only available within the area that they are installed. They will not be avail- able to other areas of the house as they are not distributed by the DH44. Run lengths of Cat-5 from any local (in-room) source to the Touch Pad located in that area.

10

©2008 • All rights reserved.

Image 12
Contents DH44 Page Safety Information All rights reservedOperating Temperatures & Environments PrecautionsCaring For the DH44 Contents Introduction Features Aton DH44 AccessoriesIndicator/Button Function Defining TermsFront Panel Rear Panel Description FunctionDH44 4 Source, 4 Zone Digital Audio Router System Design Overview/Applications PlanningPre-Wiring Applications Basic 4 Zone, 4 Source SystemBasic 4 Zone, 4 Source System w/ Local Sources Expanded 4 Source, 8-28 Zone System Expanded System 4 Sources/10 Zones + Local SourcesConnections Source Audio InputsAudio Source Source Input Digital Coaxial DH46X DH44 Source Loop Outputs Source Loop OUTD5-NET Expansion OUTIR OUT/ALL IR OUT Page/Doorbell Audio and Trigger Input PG/DB TrigAuxiliary Power Connector AUX Power OUT Zone OUTDHTP1 Rear DHTP1 Speaker Connections16/2 USB Port USBSystem Expansion Local Sources Adding ZonesDhsip IR OUT Dhsip FrontAdding Zones DH46X Digital Audio Router # of Chassis Max # of Zones DH44 x DH44 x 1/DH46X xExpansion OUT/EXPANSION Source Loop OUT/SOURCE Loop Expansion OUT/EXPANSIONCat-5 20 DX46X Zone OUT ConnectionsSettings & Operation DIP Switch SettingsSource Input Gain Keypad Pairing Analog Source Input Gain Zone Pairing Zone Pairing DIP SwitchesOperation DHTP1 Amplified Touch PadTroubleshooting Audio Symptom Possible Cause SolutionSymptom Possible Cause Solution Appendix a Specifications 35Vrms / 4.8dBu2V rms / 8.2dBu Page Limited Warranty Enrutador Digital de Audio De 4 Fuentes/4 Zonas Page Información de Seguridad Todos los derechos reservadosCuidado del DH44 Temperaturas y ambientes del funcionamientoPrecauciones Índice IntroducciónSalida IR/SALIDA Todo IR «IR OUT/ALL IR OUT» Introducción Características Accesorios DH44 AtonDefinición de Términos Indicador/Botón FunciónPanel Posterior Descripción FunciónNET Comunicación en el futuroTabla 1.2 Panel Posterior Diseño de Sistema Resumen/Aplicaciones PreparaciónPre-Cableado Pre-ConstrucciónActualización de Cableado/Post-Construcción DH44 a «Touchpads» DHTP1Usos Sistema Básico de 4 Fuentes/4 ZonasDH44 Enrutador Digital de Audio de 4 Fuentes/4 Zonas Sistema Básico de 4 Fuentes/4 Zonas con Zonas LocalesSistema Expandido de 4 Fuentes/8-28 Zonas Conexiones Entradas de Fuentes de AudioFuente de Audio Salida AnálogaDibujo 3.2 Salida de Fuente Coaxial Digital Salidas de Bucle de Fuentes Source Loop OUT Entrada de D5-NET D5-NETSalida de Expansión Expansion OUT Dibujo 3.5 Salidas de Expansión DH44 Enrutador Digital de Audio de 4 Fuentes/4 Zonas 3 4 5 6 Salida de Zona «ZONE OUT»DHTP1 OPT/COAX» en laDHTP1 Vista posterior ¼ de pulgadaConexiones de Altavoces DHTP1 Expansión del Sistema Agregando Zonas Fuentes LocalesEntrada de Fuente de Placa de Pared Dhsip DHTP1 Posterior Salida IR «IR OUT» Parte delantera de DhsipPara Agregar Zonas Enrutador Digital de Audio DH46X # de Chasis Máximo # de Zonas DH44 x DH44 x 1/DH46X xChasis DH46X adicionales DHTP1 Vista Posterior Ajustes y Funcionamiento Ajustes de Interruptores DIPFuente DE Ganacia DE Entrada Empajear LOS Teclados Fuente Análoga de Ganancia de EntradaEmparejadas No Emparejadas Emparejar ZonasFuncionamiento Problemas y Soluciones Audio Síntoma Causa Posible SoluciónSíntoma Causa Posible Solución Page Garantía limitada