Delta 31-483 Adjustments, Adjusting the Table Tilt, Squaring the Table to the Spindle

Page 11

ADJUSTMENTS

ADJUSTING THE TABLE TILT

For any bevel sanding operation, you must use a table insert with an oblong-shaped opening. Failure to do so may lead to serious injury and / or damage to machine or the

work piece.

Loosen both table tilt locking levers. (see Figure 10).

Tilt the table until the pointer is at the desired angle.

Re-tighten both locking levers.

Figure 10

SQUARING THE TABLE TO THE SPINDLE

When sanding with the table positioned at 90°, it is important that the table surface be square to the sanding spindle. Periodically, it is a good idea to ensure proper alignment between the table and spindle.

With a spindle installed, use a square to check the position of the table relative to the sanding spindle (see Figure 11). The square should be flat against the table and the spindle from both front and back.

If the table and sanding spindle are not square, use the following procedure.

Ensure the table tilt indicator is at 90°.

Unlock both table tilt levers .

Adjust the fixed stop as shown in Figure 12.

Lock both table tilt levers and use a square to re-check table/spindle alignment.

Repeat steps 2-4 until the table surface and sanding spindle are perpendicular.

Make sure the pointer reads 90°. If the pointer needs to be adjusted loosen the screw and adjust to the correct position.

Figure 11

Figure 12

11

Image 11
Contents Heavy Duty Oscillating Bench Spindle Sander Important Safety Instructions Table of ContentsGeneral Safety Rules Safety Guidelines DefinitionsRefer to them often and use them to instruct others Grounding Instructions POWER CONNECTIONSMotor Specifications EXTENSION CORDS KEY Features and ComponentsFunctional Description Product SpecificationsInstall Spindles AssemblyInstall Sanding Sleeves Onto Spindles Connect to a Dust Collector Select and Install Table InsertON-BOARD Storage for Spindles and Table Inserts OperationSquaring the Table to the Spindle AdjustmentsAdjusting the Table Tilt Warranty Recommended MaintenanceAccessories Service and Repairs Replacement PartsConsignes DE Sécurité Définitions Consignes DE Sécurité ImportantesRègles DE Sécurité Générales Conserver CES Consignes Consignes DE Mise À LA Terre RaccordementsSpécifications DU Moteur Rallonges Caractéristiques ET Composantes ImportantesDescription Quantité Description FonctionnelleSpécifications DU Produit DéballageAssemblage Installez LES Manchons DE Ponçage SUR LES BrochesInstaller LES Broches Connexion DU Collecteur DE Poussière Sélectionner ET Installer LA Plaque ’INSERTION DE TableStockage Intégré Pour Broches ET Plaques ’INSERTION DE Table FonctionnementAjuster L’ANGLE DE LA Table À LA Ponceuse AjustementsAjuster L’INCLINAISON DE LA Table Garantie Recommandations DE MaintenanceAccessoires Service ET Réparations Aide Pour LES PIÈCES, LE Service OU LA GarantieNormas DE Seguridad Definiciones Instrucciones Importantes DE SeguridadPage Guarde Estas Instrucciones Instrucciones DE Conexión a Tierra Conexiones DE AlimentaciónEspecificaciones DEL Motor Alargadores Eléctricos Características Y Componentes ClaveDescripción Cantidad Descripción FuncionalEspecificaciones DEL Producto DesembalajeInstalación DE LOS Rodillos EnsamblajeInstalación DE LAS Cintas DE Lijado EN LOS Rodillos Conexión a UN Recolector DE Polvo Selección E Instalación DEL Accesorio Para MesaFuncionamiento Cuadratura DE LA Mesa CON EL Rodillo AjustesAjuste DE LA Inclinación DE LA Mesa Garantía Mantenimiento RecomendadoAccesorios Servicio Técnico Y Reparaciones Asistencia Sobre GARANTÍA, Servicio O PiezasPage Page Airport Road Anderson, SC 800