Delta 31-483 Assembly, Install Sanding Sleeves Onto Spindles, Install Spindles

Page 8

ASSEMBLY

INSTALL SANDING SLEEVES ONTO SPINDLES

Tools Required

12mm wrench

• Phillips head screw driver

For 1/4", 1/2", & 5/8" spindles

Loosen the Phillips head screw on the bracket clamp located at the bottom of the spindle. See Figure 2.

Slide the sanding sleeve onto the spindle completely, ensuring the sleeve slides under the bracket clamp as shown.

Re-tighten the screw on the bracket clamp to secure the sleeve in place.

To ensure the sleeve is secure on the spindle, pull on the sleeve to make sure it does not slide.

For 1 ½" & 2" Spindles

NOTE: The threads at the top of the 1 ½" and 2" spindles are reverse threaded. To tighten the nut at the top of the spindle during steps 2 and 3, turn counter clockwise.

Slide the sanding sleeve onto the spindle, ensuring the bottom edge of the sleeve is even with the bottom edge of the spindle.

Using the 12 mm wrench (supplied) tighten the nut on the top of the spindle by turning counter clockwise. See Figure 3.

To ensure the sleeve is secure on the spindle, pull on it. If the sleeve slides on the spindle, continue tightening the nut at the top in ½-turn increments as needed.

Figure 2

Figure 3

INSTALL SPINDLES

NOTE: Reverse threads are used to attach the spindle to the machine.

Make sure that the switch is in “OFF" position and that the power cord is unplugged.

If installed, remove the table insert to allow better access the spindle seat.

Using a 17 mm wrench to hold the spindle seat stationary, screw the bottom threads of the spindle into the spindle seat counter clockwise until hand tight.

Use a second 17 mm wrench, placed over the retaining nut on the spindle (see Figure 4), to tighten the spindle no more than another ½ turn.

NOTE: Do not over tighten the spindle as this can make it difficult to remove later.

Figure 4

8

Image 8
Contents Heavy Duty Oscillating Bench Spindle Sander Table of Contents Important Safety InstructionsSafety Guidelines Definitions General Safety RulesRefer to them often and use them to instruct others Grounding Instructions POWER CONNECTIONSMotor Specifications KEY Features and Components EXTENSION CORDSProduct Specifications Functional DescriptionInstall Spindles AssemblyInstall Sanding Sleeves Onto Spindles Select and Install Table Insert Connect to a Dust CollectorOperation ON-BOARD Storage for Spindles and Table InsertsSquaring the Table to the Spindle AdjustmentsAdjusting the Table Tilt Warranty Recommended MaintenanceAccessories Replacement Parts Service and RepairsConsignes DE Sécurité Importantes Consignes DE Sécurité DéfinitionsRègles DE Sécurité Générales Conserver CES Consignes Consignes DE Mise À LA Terre RaccordementsSpécifications DU Moteur Caractéristiques ET Composantes Importantes RallongesDescription Fonctionnelle Spécifications DU ProduitDéballage Description QuantitéAssemblage Installez LES Manchons DE Ponçage SUR LES BrochesInstaller LES Broches Sélectionner ET Installer LA Plaque ’INSERTION DE Table Connexion DU Collecteur DE PoussièreFonctionnement Stockage Intégré Pour Broches ET Plaques ’INSERTION DE TableAjuster L’ANGLE DE LA Table À LA Ponceuse AjustementsAjuster L’INCLINAISON DE LA Table Garantie Recommandations DE MaintenanceAccessoires Aide Pour LES PIÈCES, LE Service OU LA Garantie Service ET RéparationsInstrucciones Importantes DE Seguridad Normas DE Seguridad DefinicionesPage Guarde Estas Instrucciones Instrucciones DE Conexión a Tierra Conexiones DE AlimentaciónEspecificaciones DEL Motor Características Y Componentes Clave Alargadores EléctricosDescripción Funcional Especificaciones DEL ProductoDesembalaje Descripción CantidadInstalación DE LOS Rodillos EnsamblajeInstalación DE LAS Cintas DE Lijado EN LOS Rodillos Selección E Instalación DEL Accesorio Para Mesa Conexión a UN Recolector DE PolvoFuncionamiento Cuadratura DE LA Mesa CON EL Rodillo AjustesAjuste DE LA Inclinación DE LA Mesa Garantía Mantenimiento RecomendadoAccesorios Asistencia Sobre GARANTÍA, Servicio O Piezas Servicio Técnico Y ReparacionesPage Page Airport Road Anderson, SC 800