Schumacher SI-82-6 owner manual Operating Instructions, Battery Information

Page 45

Voltage Selector Switch (model SI-70MA only)

Use this switch to set the charger to charge a 12 volt or 24 volt battery. NOTE: These chargers are not recommended for 8 or 16 volt systems.

LED Indicators

•Full Charge – When lit, this LED indicates that the battery is fully charged and the charger has stopped charging and switched to the Maintain Mode of operation (Automatic charge only).

•Power On – When lit, this LED indicates that there is AC power supplied to the battery charger.

11.OPERATING INSTRUCTIONS

This battery charger must be properly assembled in accordance with the assembly instructions before it is used.

The charger does not have an ON/OFF switch. The On and Off commands are controlled by plugging the charger into an AC electrical wall outlet only after the battery connections have been made. See the warning label on the charger for the correct input voltage.

This charger can be used with the following batteries:

BATTERY INFORMATION

Model

Type

Number of Cells

Rated Capacity

SI-82-6MA

Lead Acid (Pb)

6

20 Ah to 100 Ah

SI-70MA

Lead Acid (Pb)

6 or 12

20 Ah to 150 Ah

SI-1275A

Lead Acid (Pb)

6

20 Ah to 150 Ah

Charging

1.Ensure that all of the charger components are in place and in good working condition, for example, the plastic boots on the battery clips.

2.Connect the battery following the precautions listed in sections 6 and 7.

3.Select the appropriate settings for your battery.

4.Connect the AC power following the precautions listed in section 8. Make sure to place the charger on a dry, nonflammable surface like metal or concrete.

5.To disconnect, reverse the procedure.

Manual Charging (models SI-82-6MA and SI-70MA)

When a Manual Charge is performed, the charger will continue to charge and will not shut off. You must keep a visual check on the ammeter to determine when the battery is charged. Be sure to monitor the charging process and stop it when the battery is charged. Not doing so may cause damage to your battery or result in other property damage or personal injury.

Automatic Charging Mode

When an Automatic Charge is performed, the charger switches to the Maintain Mode (see below) automatically after the battery is charged. For a battery with a starting voltage under 1 volt, use the Manual Mode first to pre-charge the battery for five minutes, to get additional voltage into the battery for the charger to analyze.

• 41 •

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Advertencia Aviso Page Seção Página Sección PáginaTable of contents Advertencia Riego DE Gases Explosivos Riesgo DE Descarga Eléctrica O DE IncendioPage Page Precauciones Para LA Conexión DE CC Page Panel DE Control Instrucciones DE ArmadoAmperímetro a Porcentaje de cargaAGM GELArranque de motores de 75 a modelo SI-1275A únicamente Información DE LA Batería Instrucciones DE FuncionamientoModo de mantenimiento carga automática únicamente Finalización de la carga carga automática únicamenteInstrucciones DE Mantenimiento 12. Cómo Calcular EL Tiempo DE CargaInstrucciones DE Traslado Y Almacenamiento Resolución DE Problemas Causa Posible MOTIVO/SOLUCIÓNProblema Causa Posible MOTIVO/SOLUCIÓN Problema Causa Posible MOTIVO/SOLUCIÓN Antes DE Regresar Para LAS Reparaciones Placa de datos 230V, 50/60Hz Modelo Page Perigo Aviso Risco DE Gases Explosivos Risco DE Choque Elétrico OU FogoPreparação Para Carga Precauções PessoaisRisco DE Explosão E Contato COM O Ácido DA Bateria Posição do CarregadorPrecauções Para Conexão CC UMA Faísca Próxima DASiga Estas Etapas Quando a Bateria Estiver Fora do Veículo Instruções DE Montagem Aterramento e conexões do fio elétrico de CAPainel DE Controle Porcentagem de cargaInterruptor para a seleção do tipo de bateria Informações Sobre a Bateria Instruções DE OperaçãoModo Manter somente carga automática Término da operação de carga somente carga automáticaTAMANHO/TAXAS DA Bateria Taxa DE CARGA/TEMPO DE Carga 12. Cálculo do Tempo DE CargaInstruções DE Manutenção Instruções DE Transporte E ArmazenamentoSolução DE Problemas Possível Causa MOTIVO/SOLUÇÃO Problema Possível Causa MOTIVO/SOLUÇÃO Verifique se há uma conexão Antes DE Devolver O Produto Para Reparo Especificações Placa de informaçõesModelo SI-82-6MA Placa de informações 230 V, 50/60 Hz Modelo Page Page Risk of Explosive Gases Risk of Electric Shock or FirePage DC Connection Precautions Charger Location Risk of Explosion Contact with Battery AcidPage Assembly Instructions Grounding and AC power cord connectionsControl Panel Ammeter aCharge Rate Selector Switch Voltage/Amp Selector Battery Type SwitchOperating Instructions Battery InformationMaintain Mode Automatic Charge Only Using the Engine Start feature model SI-1275A onlyCompletion of Charge Automatic Charge Only Maintenance Instructions Battery SIZE/RATING Charge RATE/CHARGING TimeCalculating Charge Time Moving and Storage InstructionsTroubleshooting Problem Possible Cause REASON/SOLUTION Problem Possible Cause REASON/SOLUTION Before Returning for Repairs Specifications Data Plate 120V, 50/60Hz Model SI-82-6MAData Plate 230V, 50/60Hz Model

SI-82-6 specifications

The Schumacher SI-82-6 is a highly regarded battery charger, renowned for its efficiency and versatility in charging various types of batteries. This device is particularly popular among automotive enthusiasts, mechanics, and anyone in need of reliable battery maintenance.

One of the standout features of the SI-82-6 is its ability to charge multiple battery types, including lead-acid, gel, AGM, and deep-cycle batteries. This versatility ensures that it can cater to a wide array of vehicles, from cars and trucks to boats and recreational vehicles. The charger operates with a robust voltage rating, typically providing a perfect balance between power and safety.

The Schumacher SI-82-6 utilizes advanced microprocessor technology, which optimizes the charging process. This means that the charger not only delivers the appropriate voltage and current to the battery but also intelligently adjusts its performance during the charging cycle. This feature helps in reducing the risk of overcharging, thereby prolonging the lifespan of the battery.

Another significant advantage of the SI-82-6 is its automatic shut-off function. Once the battery is fully charged, the charger will automatically turn off, preventing any potential damage or overheating. This is a critical safety feature, particularly for those who may leave the charger unattended while it operates.

The SI-82-6 is designed with user convenience in mind. It features an easy-to-read LED display that provides real-time information on the charging status, allowing users to monitor the progress at a glance. The compact and portable design also makes it easy to store and transport, ensuring that it can be used wherever needed.

Furthermore, the charger comes equipped with reverse polarity protection, which safeguards both the charger and the battery from potential damage caused by incorrect connections.

In summary, the Schumacher SI-82-6 is a powerful and intelligent battery charger that combines efficiency with comprehensive safety features. Its ability to charge various battery types, coupled with automatic shut-off and user-friendly design, makes it a must-have tool for anyone looking to maintain their batteries effectively. With its solid construction and reliability, the SI-82-6 is a staple choice for both casual users and professional mechanics alike. Whether you are preparing your vehicle for a long drive or simply maintaining a backup battery, the Schumacher SI-82-6 stands out as a dependable solution.
Top Page Image Contents