Ingersoll-Rand IRN37-160K-CC manual Installation DRAWING−N37/45K−CC & N50/60H−CC − Air Cooled, Key

Page 35

8.0GENERAL INFORMATION

8.2INSTALLATION DRAWING−N37/45K−CC & N50/60H−CC − Air Cooled

KEY

	A	11/2” NPT Air discharge (Female) 60Hz units	G	4 x Ø 13.0mm (0,5”) Compressor should be
		11/2” BSP Air discharge (Female) 50Hz units	bolted to the floor with fourM10 (0.38”) bolts using holes
	B	Ø63mm (2.48”) Electrical inlet	shown. Seal base tofloor with cork or rubber.
	C	0.38“ NPT (Female)	H	INTELLISYS Controller
	Note: Pipe condensate drain lines separately to an open		U	Right
	drain due to differences in drain pressures.		V	Bottom
	Use drain lines at least as large as the connection.		W	Front
	Read operations manual and check local regulations
			X−X	Section through X−X
	D	Cooling airflow
			Y	Rear view
	E	Exhaust airflow
			Z	Plan view
	F	Cabinet cooling airflow

IRN37 - 160K - CC & IRN50 - 200H & IRN75 - 160K - 2S & IRN - 100 - 200H - 2S & IRN 250 - 300H - 2S	33
http://air.irco.com

Image 35

Contents Operation and Maintenance Manual AIR Compressor Group Bonded Warranty & Registered Start UP Contents Somer ForewordIf in Doubt Consult Supervision FOREWORD F.C Abbreviations & SymbolsEnergy recovery system ERSThis unit was purchased from Purchase Order DetailsRotary Screw AIR Compressor Compressed air SafetyGeneral Information Electrical MaterialsAvoid INGESTION, Skin Contact Inhalation of Fumes TransportCoolant disposal Condensate disposalDischarge air Text DecalsLift here 39540257 Rev RotationCondensate Drain Electrical power inlet Prohibition / Mandatory Information / Instructions Safety Graphic Form and Meaning of ISO SymbolsDo not stand on any service valve or Safety Coolant Separator Pressure AIR Discharge Belt Tension Filter Motor Lubrication Unpacking and Handling Receipt / HandlingReceipt Ingersoll Rand CompanyEnsure that the correct tie down points are used InstallationLocation in Plant For technical information see sectionInstallation Discharge and Condensate Piping Installation Electrical Example of voltage imbalance calculation Installation Very ImportantFuse Type 50F 70F Adjusting the Aftercooler Trim ValveCooling Water Piping Model Minimum cooling water requirement vs RangeWater quality recommendations Psi Installation SEA Watercooled Units Selected Units onlyOrifice diameter in mm Outdoor Sheltered Installation Technical INFORMATION-SINGLE Stage General InformationFlow at 7.5 Barg m3/min Minimum ambient temperature C F Weight Kg lbsCooling clean water flow l/min US 51/38 95/46 Sound pressure level dBAMax fuse size @ 550V − 575V a Cooling clean water flow l/min US 84/65 95/72Max fuse size @ 380V − 415V a Max fuse size @ 440V − 480V aN132K N160K N200H General Information Technical Information − TWO Stage 1527 5933Flow at 100 psig cfm 1100 1690KEY Installation DRAWING−N37/45K−CC & N50/60H−CC − Air CooledInstallation DRAWING− N37/45K−CC & N50/60H−CC − Water Cooled Installation Drawing − N55/75K−CC & N75/100H−CC − Air Cooled Installation DRAWING−N55/75K−CC & N75/100H−CC−Water Cooled General Information General Information General Information General Information KEY 22381206 Revision B Equipment downstream of compressor Stage only 23128994 Revision aAir/coolant Coolant Condensate Cooling water W.C. only 22099006 Revision C General Information 22402135 Revision C Process and Instrumentation Diagram N250−300H TWO StagePiping legend Stop FD Wiring Schematic N37K − N45K-CC / N50-60h−cc a/c blower vfdNumbers Function Wire color WiresLabel Description Wiring schematic n55-75k-cc / n75-100h-cc a/c Blower vfdSS1-3 Wires Numbers Function Wire colorSgne Wiring schematic n37/45k-cc/n50/60h-cc w/cColor 23131345 Revision a Wiring schematic n55-75k-cc / n75-100h-cc W/c4ATT SENSOR, Package AIR Discharge Temperature 4CTT Revision M Wiring schematic n75-160k-cc / n125-200h-cc A/c22093058 SGNe F10Revision E Wiring schematic n75-160k-cc / n125-200h-cc W/c4SV VALVE, Water Stop 6APT 380-480V SG-Ne Wiring schematic n250-300H4ATT SENSOR, Package AIR Discharge Temperature 6APT General Information General Description Basic Operation Operating InstructionsStopping the machine in an emergency Arrows Intellisys ControlsMain Menu Display ScreenCurrent Status items Current Status ScreenReady to Start Main MenuOperator Setpoints Operator Setpoints Default MIN MAX Step UnitCondensate Interval Selection MIN MAX OptionsScheduled start Sensor CalibrationClock Functions Alarm HistoryEnergy Status Messages Initial Check Alarms Service WarningsAlarm Main Menu AlarmsMaintenance Ultra Coolant Maintenance Procedures Prior to attempting any maintenance work, ensure that− Adding coolant Prior to starting Coolant level checking procedureDrain sequence for N250/300H−2S Coolant filter change procedureSeparator element checking procedure Separator element change procedureSeparator tank / Pressure system Separator element change procedure for N250/ 300H−2SScavenge screen clean/check procedure Start the compressor and check for leaks and coolant levelBlower motor Re−Grease Air filter change procedureAir filter change procedure N250/300H−2S Aircooled Cooler CleaningN50/100H N37/75K Aftercooler Watercooled Cooler CleaningHigh Airend Temperature Sensor checking procedure Coolant CoolersMoisture Separator Check / Cleaning Blower / fan Motor Bearing Maintenance Stored unitsMotor cowl cleaning N75−160 units only Drive Box Filter Removal / ReplacementFluid and Vibration Monitoring No Loss Drain Trap where fitted Check / CleaningCoolant Sampling Procedure Compressor will not No power supply to package Fault FindingGeneral Faults Symptom Fault RemedyCheck and modify settings With correct coolant Or not sealing correctlyRemove blockage, repair or replace damaged See aboveWith coolant’ Pressure transducer Fault Cause RemedyIndicated on the INTELhYS Controller Drive FaultsFault Cause Action