Delta SM600 instruction manual Following a Line, Inside Cutting

Page 16

FOLLOWING A LINE

WARNING: CUT HAZARD: Keep hands away from blade. With your scroll saw you should be able to cut a straight or curved line with ease. Most beginners will experience blade wandering; however, they eventually learn to control it as they become more familiar with the machine. Use scrap material to practice cuts before starting a project. This enables you to develop your own way of cutting and you will find out what you can and cannot do with your saw.

Always hold the work firmly against the table and do not feed the workpiece too fast while cutting. Feed the workpiece only fast enough so that the blade will cut. Scroll saws cut faster across the grain than they do with the grain. Allow for this tendency when cutting patterns that shift rather quickly from with-the-grain cuts to cross-grain cuts.

Make "relief" cuts before cutting long curves and never attempt to cut a curve that is too tight for the blade being used.

INSIDE CUTTING

Inside cutting is where the blade must be threaded through a hole in the workpiece. The Shopmaster 16" Scroll Saw has the capability of performing this operation quickly and easily as follows:

Inside cutting can be accomplished quickly with the saw. In Fig. 36, the operator has just completed one of the inside cuts and must move to the next hole.

Fig. 36

Loosen lock handle (A) Fig. 37, and raise the spring holddown (B). Release blade tension by moving tension lever (C) forward and loosen upper blade holder by moving lever (D) to the rear as shown. This will release the blade (E). Insert the blade (E) into the next hole in the pattern, as shown.

Place blade (E) Fig. 38, back into the upper blade holder and tighten blade by moving lever (D) forward. Move tension lever (C) to the rear as shown and lower spring holddown (B). You are ready to make the next inside cut.

C

A

E

D

B

Fig. 37

C

D

E

B

Fig. 38

16

Image 16
Contents Model SM600 General Safety Rules Additional Safety Rules for Scroll Saws Refer to them often Use them to instruct othersPower Connections Grounding InstructionsUnpacking and Cleaning Extension CordsScroll SAW Parts Assembly Assembly Time EstimateBCC O Page Operating Controls and Adjustments ON-OFF and Variable Speed SwitchesLocking ON-OFF Switch OFF Position Fastening Scroll SAW To Supporting SurfaceTable Insert Changing BladesPage Adjusting Blade Tension Adjusting Clamping Action of Upper Blade HolderAdjusting the Table Tilting the TableAdjusting Holddown Adjusting Dust BlowerFollowing a Line Inside CuttingLubrication Troubleshooting Blade BreakageChoice of Blade and Speed Page Page Accessories PARTS, Service or Warranty Assistance Two Year Limited WarrantySierra de Calar de 16 pulg. de Velocidad Variable Normas DE Seguridad Generales Instrucciones Antes DE Utilizar LA HerramientaReglas DE Seguridad Adicionales Para LAS Sierras DE Calar SiempreEspecificaciones DEL Motor Conexiones a LA Fuente DE Alimentaci NInstrucciones DE Conexi N a Tierra Instrucciones DE Funcionamiento Cordones DE Extensi NDesempaquetado Y Limpieza Sierra DE Calar DE Piezas Asamblea BCC O Page Ajuste DE LA Sierra DE Calar a LA Superficie DE Apoyo Controles DE Funcionamiento Y AjustesInterruptores DE ENCENDIDO/APAGADO Y DE DOS Velocidades Pieza DE Relleno DE LA Mesa Cambio DE HojasOprima la palanca de cierre del mandrino de apriete Ajustando LA Tension DE Hoja Ajustando LA Accion DE Apriete DEL Detentor DE Hoja SuperiorInclinado DE LA Mesa Ajuste DEL Reten Ajuste DEL Soplador DE PolvoSiguiendo UNA Linea Cortado InteriorSeleccion DE Hoja Y DE Velocidad LubricacionRotura DE LA Hoja Notas Accesorios PIEZAS, Servicio O Asistencia DE GarantœaPage Mode Demploi Règles Générales DE Sécurité AU Canada 505, PROM. SOUTHGATE, GUELPH, Ontario N1H 6M7Røgles DE S Curit Suppl Mentaires Pour LES Scies ¸ D Couper Conserver CES DirectivesConnexions Lectriques Semballage ET Nettoyage Directives D’UTILISATIONPiøces DE LA Scie ¸ D Couper Assemblage Temps D’ASSEMBLAGE EstimPositionner la table a , sur la machine tel quillustré Page Utilisation DES Contr LE ET R Glages Fixation DE LA Scie ¸ D Couper ¸ LA Surface DE SupportInterrupteursde MARCHE-ARR T ET DE Vitesse Variable Verrouiller L’INTERRUPTEUR EN Position D’ARR TInsert DE Table Changement DE LamesPage Glage DE LA Tension DE LA Lame Glage L’ACTION D’ TAU DU PORTE-LAME SUP RieurInclinaison DE LA Table Ajustement DE LA TableGlage DE LA Tige DE Retenue Glage DU Poussi ReurSuivre UNE Ligne Coupe INT RieureChoix DE Lame ET Vitesse Pannage Bris DE LameAccessoires PIØCES, R Paration OU Aide ¸ Propos DE LA GarantieCanadian PORTER-CABLE · Delta Service Centers