Delta SM600 instruction manual Bcc O

Page 8

5.Position table (A) Fig. 7, on the machine as shown. Align the two holes in the table trunnions (O) with the two holes in the base (P) of the machine. NOTE: BEFORE

TIGHTENING THE M6x1x45mm SPECIAL SCREWS

(B) AND M6 LOCKNUTS (C) FIG. 7, MAKE SURE THE TILT SCALE (D), IS POSITIONED INSIDE POINTER (E) AS SHOWN. ALSO, DO NOT COMPLETELY TIGHTEN THE M6x1x45mm SPECIAL SCREWS (B) AND M6 LOCKNUTS (C). TABLE MUST BE ABLE TO TILT FREELY. Fasten the table (A), to the base (P), using the two M6x1x45mm special screws (B), and M6 locknuts

(C) as shown.

6.Disassemble the handle by unscrewing and remov- ing screw and spring (F), and handle (G) from locking stud (H), as shown in Fig. 8. Place a M10 flat washer (J) on threaded end of stud (H).

7.Screw threaded end of stud (H) Fig. 9, with the M10 flat washer (J) through slot in angle of tilt scale (D) and into tapped hole (K).

OA

BCC O

B

P

P

D

 

E

 

 

Fig. 7

G

J

F

H

Fig. 8

D

K

J

H

Fig. 9

8.Place handle (G) Fig. 10, onto locking stud (H) and fasten with screw and spring (F). Move table (A) to the horizontal position and lock table (A), by turning handle

(G) clockwise.

A

F

H

G

Fig. 10

8

Image 8
Contents Model SM600 General Safety Rules Additional Safety Rules for Scroll Saws Refer to them often Use them to instruct othersPower Connections Grounding InstructionsUnpacking and Cleaning Extension CordsScroll SAW Parts Assembly Assembly Time EstimateBCC O Page Operating Controls and Adjustments ON-OFF and Variable Speed SwitchesLocking ON-OFF Switch OFF Position Fastening Scroll SAW To Supporting SurfaceTable Insert Changing BladesPage Adjusting Blade Tension Adjusting Clamping Action of Upper Blade HolderAdjusting the Table Tilting the TableAdjusting Holddown Adjusting Dust BlowerFollowing a Line Inside CuttingChoice of Blade and Speed Troubleshooting Blade BreakageLubrication Page Page Accessories PARTS, Service or Warranty Assistance Two Year Limited WarrantySierra de Calar de 16 pulg. de Velocidad Variable Normas DE Seguridad Generales Instrucciones Antes DE Utilizar LA HerramientaReglas DE Seguridad Adicionales Para LAS Sierras DE Calar SiempreInstrucciones DE Conexi N a Tierra Conexiones a LA Fuente DE Alimentaci NEspecificaciones DEL Motor Desempaquetado Y Limpieza Cordones DE Extensi NInstrucciones DE Funcionamiento Sierra DE Calar DE Piezas Asamblea BCC O Page Interruptores DE ENCENDIDO/APAGADO Y DE DOS Velocidades Controles DE Funcionamiento Y AjustesAjuste DE LA Sierra DE Calar a LA Superficie DE Apoyo Pieza DE Relleno DE LA Mesa Cambio DE HojasOprima la palanca de cierre del mandrino de apriete Ajustando LA Tension DE Hoja Ajustando LA Accion DE Apriete DEL Detentor DE Hoja SuperiorInclinado DE LA Mesa Ajuste DEL Reten Ajuste DEL Soplador DE PolvoSiguiendo UNA Linea Cortado InteriorRotura DE LA Hoja LubricacionSeleccion DE Hoja Y DE Velocidad Notas Accesorios PIEZAS, Servicio O Asistencia DE GarantœaPage Mode Demploi Règles Générales DE Sécurité AU Canada 505, PROM. SOUTHGATE, GUELPH, Ontario N1H 6M7Røgles DE S Curit Suppl Mentaires Pour LES Scies ¸ D Couper Conserver CES DirectivesConnexions Lectriques Semballage ET Nettoyage Directives D’UTILISATIONPiøces DE LA Scie ¸ D Couper Assemblage Temps D’ASSEMBLAGE EstimPositionner la table a , sur la machine tel quillustré Page Utilisation DES Contr LE ET R Glages Fixation DE LA Scie ¸ D Couper ¸ LA Surface DE SupportInterrupteursde MARCHE-ARR T ET DE Vitesse Variable Verrouiller L’INTERRUPTEUR EN Position D’ARR TInsert DE Table Changement DE LamesPage Glage DE LA Tension DE LA Lame Glage L’ACTION D’ TAU DU PORTE-LAME SUP RieurInclinaison DE LA Table Ajustement DE LA TableGlage DE LA Tige DE Retenue Glage DU Poussi ReurSuivre UNE Ligne Coupe INT RieureChoix DE Lame ET Vitesse Pannage Bris DE LameAccessoires PIØCES, R Paration OU Aide ¸ Propos DE LA GarantieCanadian PORTER-CABLE · Delta Service Centers