Black & Decker FS2407CSL, FS2406CS, FS1807CS, FS1806CSL Additional Safety Rules Circular Saws

Page 4

90508554 Circ Saws REV 8/22/06 1:22 PM Page 4

•Maintain a firm grip on the saw and position your body and arm in a way that allows you to resist KICKBACK forces. KICKBACK forces can be controlled by the operator, if proper precautions are taken.

•When blade is binding or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

•When restarting a saw in the workpiece, center the saw blade in the kerf and check that teeth are not engaged into the material. If saw blade is binding it may walk up or KICKBACK from the workpiece as the saw is restarted.

•Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

•Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK.

•Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and

KICKBACK.

•Use extra caution when making a "Pocket Cut" into existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK.

Additional Safety Rules: Circular Saws

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

•Snagging the lower guard on a surface below the material being cut can momentarily reduce operator control. The saw can lift partially out of the cut increasing the chance of blade twist. Ensure there is sufficient clearance under the workpiece.

•When necessary to raise lower guard manually, use the retracting lever.

•KEEP THE BLADES CLEAN AND SHARP. Sharp blades minimize stalling and kickback. The use of dull and/or dirty blades can increase the saw loading causing the operator to push harder which promotes twisting.

DANGER: KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades. Never place hands in front of or behind the path of the blade while cutting. Do not reach underneath work while blade is rotating. Do not attempt to remove cut material when blade is moving.

•SUPPORT LARGE PANELS. Large panels must be supported as shown in this manual to minimize the risk of blade pinching and kickback. When cutting operation requires the resting of the saw on the workpiece, the saw shall be rested on the larger portion and the smaller piece cut off.

•USE ONLY CORRECT BLADES AND BLADE ASSEMBLY COMPONENTS WHEN MOUNTING BLADES. Do not use blades with incorrect size holes. Never use defective or incorrect blade washers or bolts. Follow blade assembly procedures.

•ADJUSTMENTS. Before cutting be sure depth and bevel adjustments are tight.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Cordless 6-1/2 165mm 4 184mm Circular Saws Save this Manual for Future ReferenceElectrical Safety Personal SafetyWork Area Tool Use and CareService Causes and Operator Prevention of KickbackAdditional Safety Rules Circular Saws Guard Against Kickback Safety Instructions LasersTo Reduce the Risk of Kickback Class IIlA Laser Charging the Battery Single Port Charger Safety Warnings and Instructions ChargingCharging the Battery Dual Port Charger Important Charging Notes Battery CAP Information Overview Figure D 11a13a Cutting Depth Adjustment Figures I & J Bevel Angle Adjustment Figure KShoe Adjustment for 90 Cuts Operating Instructions General CutsAttaching and Removing the Blade Figure L Lower Blade GuardSwitch Installing the Batteries Figure NAutomatic Electric Brake On Board LaserSwitching the Laser on and OFF Adjusting the Laser Figure ORemove the SAW Battery Before Making Laser Adjustments To USE the Laser LineProblem Troubleshooting Possible Cause Possible Solution AccessoriesAbrasive Type or Metal Cutting Blades on SAW Full TWO-YEAR Home USE Warranty Service InformationRbrc Seal Numéros DE Catalogue Avec Lasers FS1806CSL Numéros DE Catalogue Sans LasersConserver CE Manuel Pour UN Usage Ultérieur Sécurité Personnelle Mesures DE Sécurité Relatives À L’ÉLECTRICITÉUtilisation ET Entretien DE L’OUTIL Mesures DE Sécurité Spécifiques EntretienMesures DE Sécurité Additionnelles Scies circulaires Cause de rebonds et mesures de préventionMesures de précaution contre les rebonds Mesures Pour Minimiser LES Risques DE RebondsDe rappel Coincement DE LA Lame OU DE Blocage DE LA ScieDirectives DE Sécurité Pour Lasers La minuteAvertissements de sécurité et directives chargement Charge DE Batterie Chargeur À Simple Sortie Méthode DE Chargement Chargeur À Double SortieInformation Concernant LE Capuchon DU BLOC-PILE Remarques Importantes DE ChargementAperçu figure D 13a Préparation pour l’assemblage et le réglage Réglage DE L’ANGLE DE Biseau Figure KFonctionnement Coupes GénéralesRéglage DE LA Semelle Pour LES Coupes DE SE Protéger DES Effets DE RebondDétente Frein Électrique AutomatiqueLaser Intégré Mise EN MARCHE/ARRÊT DU LaserRetirer LE BLOC-PILES DE LA Scie Avant DE Régler LE Laser Pour Utiliser LE Trait LaserDécoupe EN Poche Figure O SciageDépannage Accessoires DE Matières Abrasives Avec LA SciePrésente Garantie Manual DE Instrucciones Conserve Este Manual Para Futuras ConsultasArea de trabajo Seguridad ElectricaSeguridad Personal USO Y Cuidados DE LA HerramientaServicio Reglas DE Seguridad EspecificasReglas DE Seguridad Adicionales Sierras Circulares Causas DEL Contragolpe Y Prevención POR Parte DEL OperadorProtéjase contra el Contragolpe Para Reducir EL Riesgo DE ContragolpeInstrucciones DE Seguridad Para EL Láser Instrucciones y advertencias de seguridad carga Carga DE LA BATERÍA- Cargador DE UN Puerto Procedimiento DE Carga Cargador DE DOS PuertosInformación Acerca DEL Protector DE LA Batería Notas Importantes Sobre LA CargaCirc Saws REV 8/22/06 122 PM Descripción General Figura D Batería Bloqueo del eje no se muestraWrong 2726 Instrucciones DE Operación Cortes GeneralesUSO DEL Láser FS1806CSL, FS1807CS, FS2406CS, FS2407CSL only Protector inferior de la hojaInterruptor Freno Eléctrico AutomáticoLáser Incorporado EN LA Unidad Antes DE Instalar LAS BateríasApagado Y Encendido DEL Láser Aserrado Para Usar LA Línea LáserCortes Internos Figura O Problema Causa posible Solución posible LA Sierra Detección DE ProblemasAccesorios Nota especial de Garantía para Contratistas EL Sello RbrcCULIACAN, SIN MONTERREY, N.L GUADALAJARA, JALPUEBLA, PUE MEXICO, D.FCirc Saws REV 8/22/06 122 PM

FS1807CS, FS1806CS, FS2407CSL, FS1806CSL, FS2406CS specifications

The Black & Decker line of handheld vacuums, including the FS2406CS, FS1806CSL, FS2407CSL, FS1806CS, and FS1807CS, represents a blend of innovative technology and user-friendly design. These models are tailored to meet the needs of modern consumers seeking convenience and efficiency in cleaning.

The FS2406CS is designed with a powerful motor that delivers excellent suction capabilities, making it ideal for tackling everyday messes such as crumbs, pet hair, and dirt. Its lightweight construction ensures that users can maneuver it easily, while the ergonomic handle provides a comfortable grip during operation. The detachable, washable dust bowl simplifies maintenance, allowing for quick and easy emptying without the fuss of bags.

The FS1806CSL and FS2407CSL offer similar power and ease of use but incorporate additional features that cater to specific needs. These models come equipped with various attachments, including crevice tools and dusting brushes, enhancing versatility and enabling users to clean different surfaces efficiently. These attachments are particularly beneficial for reaching tight spaces or delicate surfaces.

Another standout feature across these models is the advanced filtration system. The HEPA filters trap allergens and dust particles, contributing to a healthier home environment. This aspect is particularly appreciated by allergy sufferers, as it helps reduce airborne particles significantly during the cleaning process.

The FS1806CS and FS1807CS models focus on maximizing runtime and charging convenience. With their lithium-ion batteries, users can expect longer operational periods without compromising power. The inclusion of a quick-charging dock ensures that vacuums are always ready for use, making them a practical choice for busy households.

In terms of design, all models boast a sleek and compact profile, ensuring easy storage when not in use. The color choices are thoughtfully selected to suit a variety of home aesthetics, helping them blend seamlessly into your living space.

Overall, the Black & Decker FS2406CS, FS1806CSL, FS2407CSL, FS1806CS, and FS1807CS exemplify modern vacuum technology, combining powerful suction, versatile attachments, efficient filtration, and user-friendly designs to create a range of cleaning solutions that cater to various needs and preferences. Perfect for quick cleanups or thorough cleaning sessions, these vacuums make maintaining a clean and comfortable home more accessible than ever.
Top Page Image Contents