Black & Decker FS2407CSL Switch, Automatic Electric Brake, Installing the Batteries Figure N

Page 14

90508554 Circ Saws REV 8/22/06 1:22 PM Page 14

SWITCH

Saw is equipped with a switch lock-off feature to prevent unintentional running.

•To operate the tool, press in on the lock-off button (2) from either side of the saw and hold it in as you depress the trigger switch (1).

•After you have depressed the trigger and the tool is running, release the lock-off button. The tool will continue to run as long as the trigger is depressed.

•To turn the tool off, release the trigger switch.

NOTE: This tool has no provision for locking the tool on, and the switch should never be locked on by any other means.

AUTOMATIC ELECTRIC BRAKE

Your saw is equipped with an electric blade brake which stops the saw blade within 1-1/2 seconds of trigger release. This is automatic and requires no adjustment.

Occasionally, under certain conditions, the brake will not function properly and won’t stop the saw in the 1-1/2 seconds as discussed above. If this condition occurs:

•Turn the saw on and off four or five times.

•If the problem still persists, have the tool serviced at a Black & Decker service center or company authorized service facility.

OPERATING THE LASER - (FS1806CSL, FS1807CS, FS2406CS, FS2407CSL ONLY)

INSTALLING THE BATTERIES - FIGURE N

WARNING: LASER RADIATION. BE CERTAIN THE LASER ON/OFF BUTTON IS IN THE OFF POSITION (SEE SECTION “SWITCHING THE LASER ON AND OFF) BEFORE INSTALLING BATTERIES.

Lift the battery door (25) off the laser module (4) by gently squeezing the front of the door as shown in figure N. Insert 2 fresh 1.5 volt AAA batteries making sure to match (+) and (-) terminals correctly. Reattach the battery door.

WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:

•Carefully follow all instructions and warnings on the battery label and package.

•Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the equipment.

•Do not short battery terminals.

•Do not charge batteries.

•Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type.

•Remove dead batteries immediately and dispose of per local codes.

•Do not dispose of batteries in fire.

•Keep batteries out of reach of children.

•Remove batteries if the device will not be used for several months.

“Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.”

ON BOARD LASER

Your saw is equipped with an on board laser which is turned on and off separately from the saw.

WARNING: LASER RADIATION. Never aim the beam at a workpiece with a reflective surface. Bright shiny reflective sheet steel or similar reflective surfaces are not recommended for laser use. Reflective surfaces could direct the beam back toward the operator.

DANGER: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare into the laser light source. Never aim light at another person or object other than the workpiece. Laser light can damage your eyes.

WARNING: DO NOT use tinted glasses to enhance the laser light. Tinted glasses

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Cordless 6-1/2 165mm 4 184mm Circular Saws Save this Manual for Future ReferenceWork Area Electrical SafetyPersonal Safety Tool Use and CareService Causes and Operator Prevention of KickbackAdditional Safety Rules Circular Saws To Reduce the Risk of Kickback Safety Instructions LasersGuard Against Kickback Class IIlA Laser Charging the Battery Dual Port Charger Safety Warnings and Instructions ChargingCharging the Battery Single Port Charger Important Charging Notes Battery CAP Information Overview Figure D 11a13a Cutting Depth Adjustment Figures I & J Bevel Angle Adjustment Figure KAttaching and Removing the Blade Figure L Shoe Adjustment for 90 CutsOperating Instructions General Cuts Lower Blade GuardAutomatic Electric Brake SwitchInstalling the Batteries Figure N On Board LaserRemove the SAW Battery Before Making Laser Adjustments Switching the Laser on and OFFAdjusting the Laser Figure O To USE the Laser LineAbrasive Type or Metal Cutting Blades on SAW AccessoriesProblem Troubleshooting Possible Cause Possible Solution Rbrc Seal Service InformationFull TWO-YEAR Home USE Warranty Conserver CE Manuel Pour UN Usage Ultérieur Numéros DE Catalogue Sans LasersNuméros DE Catalogue Avec Lasers FS1806CSL Utilisation ET Entretien DE L’OUTIL Mesures DE Sécurité Relatives À L’ÉLECTRICITÉSécurité Personnelle Mesures DE Sécurité Spécifiques EntretienMesures DE Sécurité Additionnelles Scies circulaires Cause de rebonds et mesures de préventionDe rappel Mesures de précaution contre les rebondsMesures Pour Minimiser LES Risques DE Rebonds Coincement DE LA Lame OU DE Blocage DE LA ScieDirectives DE Sécurité Pour Lasers La minuteAvertissements de sécurité et directives chargement Charge DE Batterie Chargeur À Simple Sortie Méthode DE Chargement Chargeur À Double SortieInformation Concernant LE Capuchon DU BLOC-PILE Remarques Importantes DE ChargementAperçu figure D 13a Préparation pour l’assemblage et le réglage Réglage DE L’ANGLE DE Biseau Figure KRéglage DE LA Semelle Pour LES Coupes DE FonctionnementCoupes Générales SE Protéger DES Effets DE RebondDétente Frein Électrique AutomatiqueRetirer LE BLOC-PILES DE LA Scie Avant DE Régler LE Laser Laser IntégréMise EN MARCHE/ARRÊT DU Laser Pour Utiliser LE Trait LaserDépannage SciageDécoupe EN Poche Figure O Accessoires DE Matières Abrasives Avec LA SciePrésente Garantie Manual DE Instrucciones Conserve Este Manual Para Futuras ConsultasSeguridad Personal Area de trabajoSeguridad Electrica USO Y Cuidados DE LA HerramientaServicio Reglas DE Seguridad EspecificasReglas DE Seguridad Adicionales Sierras Circulares Causas DEL Contragolpe Y Prevención POR Parte DEL OperadorProtéjase contra el Contragolpe Para Reducir EL Riesgo DE ContragolpeInstrucciones DE Seguridad Para EL Láser Instrucciones y advertencias de seguridad carga Carga DE LA BATERÍA- Cargador DE UN Puerto Procedimiento DE Carga Cargador DE DOS PuertosInformación Acerca DEL Protector DE LA Batería Notas Importantes Sobre LA CargaCirc Saws REV 8/22/06 122 PM Descripción General Figura D Batería Bloqueo del eje no se muestraWrong 2726 Instrucciones DE Operación Cortes GeneralesInterruptor USO DEL Láser FS1806CSL, FS1807CS, FS2406CS, FS2407CSL onlyProtector inferior de la hoja Freno Eléctrico AutomáticoApagado Y Encendido DEL Láser Antes DE Instalar LAS BateríasLáser Incorporado EN LA Unidad Cortes Internos Figura O Para Usar LA Línea LáserAserrado Accesorios LA Sierra Detección DE ProblemasProblema Causa posible Solución posible Nota especial de Garantía para Contratistas EL Sello RbrcPUEBLA, PUE CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL MEXICO, D.FCirc Saws REV 8/22/06 122 PM

FS1807CS, FS1806CS, FS2407CSL, FS1806CSL, FS2406CS specifications

The Black & Decker line of handheld vacuums, including the FS2406CS, FS1806CSL, FS2407CSL, FS1806CS, and FS1807CS, represents a blend of innovative technology and user-friendly design. These models are tailored to meet the needs of modern consumers seeking convenience and efficiency in cleaning.

The FS2406CS is designed with a powerful motor that delivers excellent suction capabilities, making it ideal for tackling everyday messes such as crumbs, pet hair, and dirt. Its lightweight construction ensures that users can maneuver it easily, while the ergonomic handle provides a comfortable grip during operation. The detachable, washable dust bowl simplifies maintenance, allowing for quick and easy emptying without the fuss of bags.

The FS1806CSL and FS2407CSL offer similar power and ease of use but incorporate additional features that cater to specific needs. These models come equipped with various attachments, including crevice tools and dusting brushes, enhancing versatility and enabling users to clean different surfaces efficiently. These attachments are particularly beneficial for reaching tight spaces or delicate surfaces.

Another standout feature across these models is the advanced filtration system. The HEPA filters trap allergens and dust particles, contributing to a healthier home environment. This aspect is particularly appreciated by allergy sufferers, as it helps reduce airborne particles significantly during the cleaning process.

The FS1806CS and FS1807CS models focus on maximizing runtime and charging convenience. With their lithium-ion batteries, users can expect longer operational periods without compromising power. The inclusion of a quick-charging dock ensures that vacuums are always ready for use, making them a practical choice for busy households.

In terms of design, all models boast a sleek and compact profile, ensuring easy storage when not in use. The color choices are thoughtfully selected to suit a variety of home aesthetics, helping them blend seamlessly into your living space.

Overall, the Black & Decker FS2406CS, FS1806CSL, FS2407CSL, FS1806CS, and FS1807CS exemplify modern vacuum technology, combining powerful suction, versatile attachments, efficient filtration, and user-friendly designs to create a range of cleaning solutions that cater to various needs and preferences. Perfect for quick cleanups or thorough cleaning sessions, these vacuums make maintaining a clean and comfortable home more accessible than ever.
Top Page Image Contents