Black & Decker FS1806CSL, FS2406CS, FS1807CS, FS2407CSL Safety Warnings and Instructions Charging

Page 7

90508554 Circ Saws REV 8/22/06 1:22 PM Page 7

SAFETY WARNINGS AND INSTRUCTIONS: CHARGING

1.This manual contains important safety and operating instructions.

2.Before using battery charger, read all instructions and cautionary warnings on battery charger and product using battery.

CAUTION: To reduce the risk of injury, use charger only with this product. Batteries in other products may burst causing personal injury or damage.

3.Do not expose charger to rain or snow.

4.Use of an attachment not recommended may result in a risk of fire, electric shock, or injury to persons.

5.To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.

6.Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

7.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with

2-wire or 3-wire extension cords. Only round jacketed extension cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for outdoor use can also be used for indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable for outdoor use.

b.An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size for the total length.

8.Use only the specified charger when charging your tool. The use of any other charger could damage the tool or create a hazardous condition.

9.Use only one charger when charging.

10.Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center.

11.DO NOT incinerate the tool or batteries even if they are severely damaged or completely worn out. The batteries can explode in a fire.

12.A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:

a.Wash quickly with soap and water.

b.Neutralize with a mild acid such as lemon juice or vinegar.

c.If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.

CHARGING THE BATTERY - SINGLE PORT CHARGER

THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power. NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V AC.

1.Plug the charger into any standard 120 Volt 60 Hz electrical outlet.

2.Slide the charger onto the battery pack as shown in Figure A and let it charge initially for 9 hours. After the initial charge, under normal usage, your power pack should be fully charged in 3 to 9 hours.

3.Remove pack from the charger and place in tool. NOTE: To remove the battery from the saw, press down on the release button on the back of the battery (Figure B) and pull out.

CHARGING THE BATTERY - DUAL PORT CHARGER

1.Plug the charger into an appropriate outlet.

2.Insert 1 or 2 batteries into the charger (Figure AA). NOTE: Charge time is the same for multiple batteries.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Save this Manual for Future Reference Cordless 6-1/2 165mm 4 184mm Circular SawsTool Use and Care Electrical SafetyPersonal Safety Work AreaCauses and Operator Prevention of Kickback ServiceAdditional Safety Rules Circular Saws Guard Against Kickback Safety Instructions LasersTo Reduce the Risk of Kickback Class IIlA Laser Charging the Battery Single Port Charger Safety Warnings and Instructions ChargingCharging the Battery Dual Port Charger Important Charging Notes Battery CAP Information 11a Overview Figure D13a Bevel Angle Adjustment Figure K Cutting Depth Adjustment Figures I & JLower Blade Guard Shoe Adjustment for 90 CutsOperating Instructions General Cuts Attaching and Removing the Blade Figure LOn Board Laser SwitchInstalling the Batteries Figure N Automatic Electric BrakeTo USE the Laser Line Switching the Laser on and OFFAdjusting the Laser Figure O Remove the SAW Battery Before Making Laser AdjustmentsProblem Troubleshooting Possible Cause Possible Solution AccessoriesAbrasive Type or Metal Cutting Blades on SAW Full TWO-YEAR Home USE Warranty Service InformationRbrc Seal Numéros DE Catalogue Avec Lasers FS1806CSL Numéros DE Catalogue Sans LasersConserver CE Manuel Pour UN Usage Ultérieur Sécurité Personnelle Mesures DE Sécurité Relatives À L’ÉLECTRICITÉUtilisation ET Entretien DE L’OUTIL Entretien Mesures DE Sécurité SpécifiquesCause de rebonds et mesures de prévention Mesures DE Sécurité Additionnelles Scies circulairesCoincement DE LA Lame OU DE Blocage DE LA Scie Mesures de précaution contre les rebondsMesures Pour Minimiser LES Risques DE Rebonds De rappelLa minute Directives DE Sécurité Pour LasersAvertissements de sécurité et directives chargement Méthode DE Chargement Chargeur À Double Sortie Charge DE Batterie Chargeur À Simple SortieRemarques Importantes DE Chargement Information Concernant LE Capuchon DU BLOC-PILEAperçu figure D 13a Réglage DE L’ANGLE DE Biseau Figure K Préparation pour l’assemblage et le réglageSE Protéger DES Effets DE Rebond FonctionnementCoupes Générales Réglage DE LA Semelle Pour LES Coupes DEFrein Électrique Automatique DétentePour Utiliser LE Trait Laser Laser IntégréMise EN MARCHE/ARRÊT DU Laser Retirer LE BLOC-PILES DE LA Scie Avant DE Régler LE LaserDécoupe EN Poche Figure O SciageDépannage DE Matières Abrasives Avec LA Scie AccessoiresPrésente Garantie Conserve Este Manual Para Futuras Consultas Manual DE InstruccionesUSO Y Cuidados DE LA Herramienta Area de trabajoSeguridad Electrica Seguridad PersonalReglas DE Seguridad Especificas ServicioCausas DEL Contragolpe Y Prevención POR Parte DEL Operador Reglas DE Seguridad Adicionales Sierras CircularesPara Reducir EL Riesgo DE Contragolpe Protéjase contra el ContragolpeInstrucciones DE Seguridad Para EL Láser Instrucciones y advertencias de seguridad carga Procedimiento DE Carga Cargador DE DOS Puertos Carga DE LA BATERÍA- Cargador DE UN PuertoNotas Importantes Sobre LA Carga Información Acerca DEL Protector DE LA BateríaCirc Saws REV 8/22/06 122 PM Batería Bloqueo del eje no se muestra Descripción General Figura DWrong 2726 Cortes Generales Instrucciones DE OperaciónFreno Eléctrico Automático USO DEL Láser FS1806CSL, FS1807CS, FS2406CS, FS2407CSL onlyProtector inferior de la hoja InterruptorLáser Incorporado EN LA Unidad Antes DE Instalar LAS BateríasApagado Y Encendido DEL Láser Aserrado Para Usar LA Línea LáserCortes Internos Figura O Problema Causa posible Solución posible LA Sierra Detección DE ProblemasAccesorios EL Sello Rbrc Nota especial de Garantía para ContratistasMEXICO, D.F CULIACAN, SIN MONTERREY, N.LGUADALAJARA, JAL PUEBLA, PUECirc Saws REV 8/22/06 122 PM

FS1807CS, FS1806CS, FS2407CSL, FS1806CSL, FS2406CS specifications

The Black & Decker line of handheld vacuums, including the FS2406CS, FS1806CSL, FS2407CSL, FS1806CS, and FS1807CS, represents a blend of innovative technology and user-friendly design. These models are tailored to meet the needs of modern consumers seeking convenience and efficiency in cleaning.

The FS2406CS is designed with a powerful motor that delivers excellent suction capabilities, making it ideal for tackling everyday messes such as crumbs, pet hair, and dirt. Its lightweight construction ensures that users can maneuver it easily, while the ergonomic handle provides a comfortable grip during operation. The detachable, washable dust bowl simplifies maintenance, allowing for quick and easy emptying without the fuss of bags.

The FS1806CSL and FS2407CSL offer similar power and ease of use but incorporate additional features that cater to specific needs. These models come equipped with various attachments, including crevice tools and dusting brushes, enhancing versatility and enabling users to clean different surfaces efficiently. These attachments are particularly beneficial for reaching tight spaces or delicate surfaces.

Another standout feature across these models is the advanced filtration system. The HEPA filters trap allergens and dust particles, contributing to a healthier home environment. This aspect is particularly appreciated by allergy sufferers, as it helps reduce airborne particles significantly during the cleaning process.

The FS1806CS and FS1807CS models focus on maximizing runtime and charging convenience. With their lithium-ion batteries, users can expect longer operational periods without compromising power. The inclusion of a quick-charging dock ensures that vacuums are always ready for use, making them a practical choice for busy households.

In terms of design, all models boast a sleek and compact profile, ensuring easy storage when not in use. The color choices are thoughtfully selected to suit a variety of home aesthetics, helping them blend seamlessly into your living space.

Overall, the Black & Decker FS2406CS, FS1806CSL, FS2407CSL, FS1806CS, and FS1807CS exemplify modern vacuum technology, combining powerful suction, versatile attachments, efficient filtration, and user-friendly designs to create a range of cleaning solutions that cater to various needs and preferences. Perfect for quick cleanups or thorough cleaning sessions, these vacuums make maintaining a clean and comfortable home more accessible than ever.
Top Page Image Contents