HP 600n Print Server for Token Ring manual Identify Your HP JetDirect 600N Internal Print Server

Page 16

Step 1. Identify Your HP JetDirect 600N Internal Print Server

Remove the HP JetDirect card from its packaging and verify that you have the correct card for your network.

HP J3110A for Ethernet and IEEE 802.3 Type 10Base-T networks (10 Mbps).

This card provides a single RJ-45 connector for networks that use unshielded twisted-pair cables.

HP J3111A for Ethernet, IEEE

802.3Type 10Base-T/10Base-2 networks (10 Mbps), and LocalTalk networks.

This card provides an RJ-45 connector for networks that use unshielded twisted-pair cables, a BNC connector for ThinLAN coaxial cables, and a Mini-DIN 8 connector for a LocalTalk connector box.

You can use the LocalTalk port and only one Ethernet port: RJ-45 or BNC.

2-2 Installing the Print Server

Image 16

Contents HP JetDirect 600N Hardware Installation Guide Page Hardware Installation Guide HP JetDirect 600N Print Server Publication number Quick Installation Identify Your HP JetDirect 600N Internal Print ServerHP J3110A for Ethernet 10Base-T networks HP J3112A for Token Ring Ieee 802.5 networksIf Necessary, Set Switches or Jumpers on Your Card Before Installing the Card, Verify That Your Printer WorksPrint a Printer Configuration If You Have a Token Ring CardTurn on the printer and print another configuration Verify That the Card Is Operating ProperlyConfigure the Card for Network Operation Table of Contents Using the Embedded Web Server Introduction Supported Network Protocols TCP/IPSupported Printers IntroductionIntroduction Installing the Print Server What You Need for Installation Identify Your HP JetDirect 600N Internal Print Server You can use only one Token Ring port RJ-45 or DB If Necessary, Set Switches or Jumpers on Your Card 10/100 Half/Full AutonegotiationBefore Installing the Card, Verify That Your Printer Works HP LaserJet Printers and MopiersService Config HP DesignJet PrintersTypical Card Installation and Network Connection Turn Off Your Printer and Insert the CardVerify That the Card Was Installed Correctly For HP J3113A 10/100Base-TX cards See For LocalTalk-Only Customers If you areConfigure the Card for Network Operation HP JetDirect Administrator’s Guide provided on Installing the Print Server Control Panel Configuration Introduction To Restore Configuration Default Values To Enable or Disable Network ProtocolsTo enable or disable network protocols Press Select. CFG NETWORK=YES* appearsConfiguring IPX Frame Types IPX Frame Types on an HP JetDirect Ethernet CardIPX Frame Types on an HP JetDirect Token Ring Card Frame Type DescriptionTo configure an IPX frame type CFG IPX/SPX=NO* is displayedTo configure IPX source routing Configuring IPX Source Routing Token Ring Cards OnlySource Routing Description Press Item until SRC RC=Source Routing* appears Configuring TCP/IP Parameters Parameter DescriptionTo configure TCP/IP parameters CFG TCP/IP=NO* is displayed Press Item. Etalk PHASE=1* or Etalk PHASE=2* appears To configure EtherTalk parametersCFG ETALK=NO* is displayed Control Panel Configuration Using the Embedded Web Server HP Web JetAdmin Compatibility Supported Web BrowsersViewing the Embedded Web Server Embedded Web ServerOperating Notes Link-Speed LEDs HP J3113A 10/100Base-TX Print Server Supported LinksLED State Description Off Not linked Jumper Setting Descriptions Link Configuration Jumper SettingsJumper Location Link Troubleshooting Parameter Expected Messages for 10/100TX CardsHP J3113A 10/100Base-TX Print Server Specifications and Regulatory Statements HP JetDirect 600N Internal Print ServerElectrical EnvironmentalElectromagnetic Regulatory StatementsFCC Statements Specifications Regulatory European CommunitySpecifications and Regulatory Statements Canada AustraliaVcci Class a Japan RRL Statement Korea Taiwan Class a Chinese Safety Statement Page 5969-3561