HP 600n Print Server for Fast Ethernet, 600n Print Server for Token Ring manual Quick Installation

Page 5

Quick Installation

Note	See chapter 2 for detailed information.

1.Identify Your HP JetDirect 600N Internal Print Server

HP J3110A for Ethernet (10Base-T) networks

Provides an RJ-45 connector (unshielded twisted-pair cable)

HP J3111A for Ethernet (10Base-T, 10Base-2) and LocalTalk networks

Provides an RJ-45 connector (unshielded twisted-pair cable), a BNC connector (coaxial ThinLAN cable) and Mini-DIN 8 connector (LocalTalk connector box)

HP J3112A for Token Ring (IEEE 802.5) networks

Provides an RJ-45 connector (unshielded twisted-pair cable) and DB-9 connector (type 1, 2, or 6 shielded twisted-pair cable)

HP J3113A for Fast Ethernet

(10/100Base-TX) networks

Provides an RJ-45 connector (unshielded twisted-pair cable). For 100Base-TX, use Category 5 cable.

3

Image 5

Contents HP JetDirect 600N Hardware Installation Guide Page Hardware Installation Guide HP JetDirect 600N Print Server Publication number Identify Your HP JetDirect 600N Internal Print Server Quick InstallationHP J3110A for Ethernet 10Base-T networks HP J3112A for Token Ring Ieee 802.5 networksBefore Installing the Card, Verify That Your Printer Works If Necessary, Set Switches or Jumpers on Your CardPrint a Printer Configuration If You Have a Token Ring CardVerify That the Card Is Operating Properly Turn on the printer and print another configurationConfigure the Card for Network Operation Table of Contents Using the Embedded Web Server Introduction TCP/IP Supported Network ProtocolsIntroduction Supported PrintersIntroduction Installing the Print Server What You Need for Installation Identify Your HP JetDirect 600N Internal Print Server You can use only one Token Ring port RJ-45 or DB 10/100 Half/Full Autonegotiation If Necessary, Set Switches or Jumpers on Your CardHP LaserJet Printers and Mopiers Before Installing the Card, Verify That Your Printer WorksHP DesignJet Printers Service ConfigTurn Off Your Printer and Insert the Card Typical Card Installation and Network ConnectionVerify That the Card Was Installed Correctly For LocalTalk-Only Customers If you are For HP J3113A 10/100Base-TX cards SeeConfigure the Card for Network Operation HP JetDirect Administrator’s Guide provided on Installing the Print Server Control Panel Configuration Introduction To Enable or Disable Network Protocols To Restore Configuration Default ValuesPress Select. CFG NETWORK=YES* appears To enable or disable network protocolsIPX Frame Types on an HP JetDirect Ethernet Card Configuring IPX Frame TypesIPX Frame Types on an HP JetDirect Token Ring Card Frame Type DescriptionCFG IPX/SPX=NO* is displayed To configure an IPX frame typeSource Routing Description Configuring IPX Source Routing Token Ring Cards OnlyTo configure IPX source routing Press Item until SRC RC=Source Routing* appears Parameter Description Configuring TCP/IP ParametersTo configure TCP/IP parameters CFG TCP/IP=NO* is displayed CFG ETALK=NO* is displayed To configure EtherTalk parametersPress Item. Etalk PHASE=1* or Etalk PHASE=2* appears Control Panel Configuration Using the Embedded Web Server Supported Web Browsers HP Web JetAdmin CompatibilityEmbedded Web Server Viewing the Embedded Web ServerOperating Notes LED State Description Off Not linked HP J3113A 10/100Base-TX Print Server Supported LinksLink-Speed LEDs Jumper Location Link Configuration Jumper SettingsJumper Setting Descriptions Parameter Expected Messages for 10/100TX Cards Link TroubleshootingHP J3113A 10/100Base-TX Print Server HP JetDirect 600N Internal Print Server Specifications and Regulatory StatementsElectrical EnvironmentalFCC Statements Regulatory StatementsElectromagnetic European Community Specifications RegulatorySpecifications and Regulatory Statements Vcci Class a Japan RRL Statement Korea Taiwan Class a AustraliaCanada Chinese Safety Statement Page 5969-3561