HP 600n Print Server for Ethernet manual HP J3113A 10/100Base-TX Print Server Supported Links

Page 43

A

HP J3113A 10/100Base-TX Print Server

Supported Links

HP J3113A 10/100 Base-TX print servers support 10 or 100 Mbps operation using full-duplex or half-duplex transmission channels.

When connecting to network devices that do not support autonegotiation, the print server will configure itself for 10-Mbpsor 100-Mbpshalf-duplexoperation. For example, when connected to a non-negotiating 10 Mbps hub, the print server card will automatically set itself to operate at 10-Mbpshalf-duplex.

If the card is not able to connect to the network through autonegotiation, you can manually set the link operating mode using link configuration jumpers (P1, P2, and P3) on the card.

Link-Speed LEDs

The HP J3113A print server provides 2 light-emitting diodes (LEDs) near the RJ-45 connector. These LEDs indicate the operating link speed of the print server.

LED State	Description

Off	Not linked

On	Link established
	at either 10 Mbps
	or 100 Mbps

LEDs

HP J3113A 10/100Base-TX Print Server A-1

Image 43

Contents HP JetDirect 600N Hardware Installation Guide Page Hardware Installation Guide HP JetDirect 600N Print Server Publication number HP J3112A for Token Ring Ieee 802.5 networks Quick InstallationIdentify Your HP JetDirect 600N Internal Print Server HP J3110A for Ethernet 10Base-T networksIf You Have a Token Ring Card If Necessary, Set Switches or Jumpers on Your CardBefore Installing the Card, Verify That Your Printer Works Print a Printer ConfigurationVerify That the Card Is Operating Properly Turn on the printer and print another configurationConfigure the Card for Network Operation Table of Contents Using the Embedded Web Server Introduction TCP/IP Supported Network ProtocolsIntroduction Supported PrintersIntroduction Installing the Print Server What You Need for Installation Identify Your HP JetDirect 600N Internal Print Server You can use only one Token Ring port RJ-45 or DB 10/100 Half/Full Autonegotiation If Necessary, Set Switches or Jumpers on Your CardHP LaserJet Printers and Mopiers Before Installing the Card, Verify That Your Printer WorksHP DesignJet Printers Service ConfigTurn Off Your Printer and Insert the Card Typical Card Installation and Network ConnectionVerify That the Card Was Installed Correctly For LocalTalk-Only Customers If you are For HP J3113A 10/100Base-TX cards SeeConfigure the Card for Network Operation HP JetDirect Administrator’s Guide provided on Installing the Print Server Control Panel Configuration Introduction To Enable or Disable Network Protocols To Restore Configuration Default ValuesPress Select. CFG NETWORK=YES* appears To enable or disable network protocolsFrame Type Description Configuring IPX Frame TypesIPX Frame Types on an HP JetDirect Ethernet Card IPX Frame Types on an HP JetDirect Token Ring CardCFG IPX/SPX=NO* is displayed To configure an IPX frame typeTo configure IPX source routing Configuring IPX Source Routing Token Ring Cards OnlySource Routing Description Press Item until SRC RC=Source Routing* appears Parameter Description Configuring TCP/IP ParametersTo configure TCP/IP parameters CFG TCP/IP=NO* is displayed Press Item. Etalk PHASE=1* or Etalk PHASE=2* appears To configure EtherTalk parametersCFG ETALK=NO* is displayed Control Panel Configuration Using the Embedded Web Server Supported Web Browsers HP Web JetAdmin CompatibilityEmbedded Web Server Viewing the Embedded Web ServerOperating Notes Link-Speed LEDs HP J3113A 10/100Base-TX Print Server Supported LinksLED State Description Off Not linked Jumper Setting Descriptions Link Configuration Jumper SettingsJumper Location Parameter Expected Messages for 10/100TX Cards Link TroubleshootingHP J3113A 10/100Base-TX Print Server Environmental Specifications and Regulatory StatementsHP JetDirect 600N Internal Print Server ElectricalElectromagnetic Regulatory StatementsFCC Statements European Community Specifications RegulatorySpecifications and Regulatory Statements Canada AustraliaVcci Class a Japan RRL Statement Korea Taiwan Class a Chinese Safety Statement Page 5969-3561