HP 600n Print Server Ethernet/LocalTalk manual If Necessary, Set Switches or Jumpers on Your Card

Page 6

2.If Necessary, Set Switches or Jumpers on Your Card

If You Have a Token Ring Card

Token Ring networks operate at

4 Mbps or 16 Mbps. You must set the Data Rate switch on the card to either 4 or 16, depending on your network. If you don’t know, ask your network administrator. The factory default is 16 Mbps.

If You Have a 10/100Base-TX Card

The 10/100TX card is preconfigured for Autonegotiation (jumper P1), which means the card will automatically attempt to connect to your network using the proper speed (10 or 100 Mbps) and duplex mode (Full or Half). In most cases, you do not need to change the jumper settings. Refer to Appendix A for more information.

3.Before Installing the Card, Verify That Your Printer Works.

Print a Printer

Configuration Page.

For instructions, see chapter 2 or refer to your printer manuals.

4

Image 6

Contents HP JetDirect 600N Hardware Installation Guide Page Hardware Installation Guide HP JetDirect 600N Print Server Publication number HP J3110A for Ethernet 10Base-T networks Quick InstallationIdentify Your HP JetDirect 600N Internal Print Server HP J3112A for Token Ring Ieee 802.5 networksPrint a Printer Configuration If Necessary, Set Switches or Jumpers on Your CardBefore Installing the Card, Verify That Your Printer Works If You Have a Token Ring CardTurn on the printer and print another configuration Verify That the Card Is Operating ProperlyConfigure the Card for Network Operation Table of Contents Using the Embedded Web Server Introduction Supported Network Protocols TCP/IPSupported Printers IntroductionIntroduction Installing the Print Server What You Need for Installation Identify Your HP JetDirect 600N Internal Print Server You can use only one Token Ring port RJ-45 or DB If Necessary, Set Switches or Jumpers on Your Card 10/100 Half/Full AutonegotiationBefore Installing the Card, Verify That Your Printer Works HP LaserJet Printers and MopiersService Config HP DesignJet PrintersTypical Card Installation and Network Connection Turn Off Your Printer and Insert the CardVerify That the Card Was Installed Correctly For HP J3113A 10/100Base-TX cards See For LocalTalk-Only Customers If you areConfigure the Card for Network Operation HP JetDirect Administrator’s Guide provided on Installing the Print Server Control Panel Configuration Introduction To Restore Configuration Default Values To Enable or Disable Network ProtocolsTo enable or disable network protocols Press Select. CFG NETWORK=YES* appearsIPX Frame Types on an HP JetDirect Token Ring Card Configuring IPX Frame TypesIPX Frame Types on an HP JetDirect Ethernet Card Frame Type DescriptionTo configure an IPX frame type CFG IPX/SPX=NO* is displayedConfiguring IPX Source Routing Token Ring Cards Only To configure IPX source routingSource Routing Description Press Item until SRC RC=Source Routing* appears Configuring TCP/IP Parameters Parameter DescriptionTo configure TCP/IP parameters CFG TCP/IP=NO* is displayed To configure EtherTalk parameters Press Item. Etalk PHASE=1* or Etalk PHASE=2* appearsCFG ETALK=NO* is displayed Control Panel Configuration Using the Embedded Web Server HP Web JetAdmin Compatibility Supported Web BrowsersViewing the Embedded Web Server Embedded Web ServerOperating Notes HP J3113A 10/100Base-TX Print Server Supported Links Link-Speed LEDsLED State Description Off Not linked Link Configuration Jumper Settings Jumper Setting DescriptionsJumper Location Link Troubleshooting Parameter Expected Messages for 10/100TX CardsHP J3113A 10/100Base-TX Print Server Electrical Specifications and Regulatory StatementsHP JetDirect 600N Internal Print Server EnvironmentalRegulatory Statements ElectromagneticFCC Statements Specifications Regulatory European CommunitySpecifications and Regulatory Statements Australia CanadaVcci Class a Japan RRL Statement Korea Taiwan Class a Chinese Safety Statement Page 5969-3561